This is a genuine manufacturer-supplied replacement which is specially designed for use with Metabo power tools. The purpose of a brush is to conduct the crurrent in an electric motor that powers the tool. Unfortunately, the material will wear out and it may cause intermittent performance eventually requiring a replacement. Keep in mind this high-quality brush is sold in a pack of two. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem. Please refer to the appropriate diagrams and the owners manual for the exact location and installation of these components. Not sure if your carbon brush is causing your motor problems? See our power tool repair article: <a href="http://www.ereplacementparts.com/whodunnit-the-brushes-the-switch-c-8873_8875.html" target=blank><u>Whodunnit? The brushes or the switch?</u></a>
Troubleshooting
This part works with the following brands:
Metabo
Metabo HPT
This part works with the following products:
Angle Grinder
Belt or Drum Sander
Jig Saw
Part# 316034930 replaces these:
316034930,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(10 Reviews)
Click to filter by ratings:
5 stars
10
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
great to find parts for tools fast shipping
great to find parts instead of buying new tools
Guest - September 26, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair.
The part arrived quickly and the brushes fit perfectly. The drill works like new!
Guest - April 10, 2020
Verified Purchase
★★★★★
★★★★★
it was ok
ok
Guest - October 7, 2020
Verified Purchase
★★★★★
★★★★★
Easy install
It was the right parts and it was an easy install with the help of the video.
Guest - March 5, 2021
Verified Purchase
★★★★★
★★★★★
Easy repair
Easy to order part was right
Guest - April 7, 2021
Verified Purchase
★★★★★
★★★★★
Easy repair parts on time oem replacement. Works like new ent
Matches oem part perfect.
Easy repair
Works perfectly
Guest - May 12, 2021
Verified Purchase
★★★★★
★★★★★
The right parts
The brushes I ordered were the correct parts and arrived quickly. Very pleased.
Guest - November 17, 2021
Verified Purchase
★★★★★
★★★★★
Good service
Right fit and good product
Guest - June 15, 2022
Verified Purchase
★★★★★
★★★★★
Happy to have found these so easily
I tried the brands website and found nothing. I found them right away on eParts!
Guest - August 2, 2022
Verified Purchase
★★★★★
★★★★★
Very easy repair
Parts arrived on time as scheduled, and we're an exact match
Guest - May 19, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Disassembled outer casing to discover worn brushes. Replaced brushes.
2. Discovered a worn bearing which caused excessive play on the shaft, replaced that too.
3. Also replaced the clamping nut which holds on cut off wheel/flap disc/whatever you are using.
Took me about 20min or more, but I wasn\'t in a rush.
Removed the screws holding the handle together. Removed the brushes with help from the needle nose pliers to pull up the springs. Installed the new brushes and springs and put the handles back together.
Works great.
Removed 3 screws holding the clam shell housing together using a Torx head screwdriver.
Remove both pieces of the housing from the frame of the grinder.
Using a small tip screwdriver, gently pry the spring clips up and over to the side, clearing the pathway of the brush holder.
Using small needle nose pliers, pull to rem
... Read moreove the wire connector attaching the brush wires to the holders.
Pull the old brushes up and out of the holders paying attention to the orientation of the wire attached to the brush.
Insert the new brush into the opening of the holder making sure the wire is on the topside of the brush and in the same orientation as the old one removed.
Reposition the spring clips to hold the top of the brushes against the commutator of the rotor.
Attach the brush wires by pushing the wire connector back onto the tab of the holder.
Replace plastic housing and tighten screws making sure there are no gaps in the seam once tight.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10416276
Manufacturer Part Number: 316034930
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 316034930 Metabo Carbon Brush Set")
_WW_1.gif "Part Location Diagram of 316034930 Metabo Carbon Brush Set")
