Close
Phone 1-855-343-0069
Cart
Official OEM Guarantee
Fast shipping from USA
365 Day Returns
Preferred Brand Partners
10181415-1-M-DeWALT-611540-00-Switch Support
Part Location Diagram of 611540-00 DeWALT Switch Support
See part 137 in the diagram
( Grid squares measure 1x1 inch )
10181415-1-S-DeWALT-611540-00-Switch Support Part Location Diagram of 611540-00 DeWALT Switch Support

Switch Support 611540-00

Manufactured by:
DeWALT
ERP Number:
ERP10181415
Part Number:
611540-00
Original Equipment Manufacturer ?
  Works with your model  DW821!
$6.16
Special Order

A Bit Difficult 

30 - 60 mins 

(1 rated repair) ?
  Works with your model   DW821!

Jump to:

Troubleshooting Repair Instructions Model Cross Reference

Troubleshooting

This part works with the following brands:
  • DeWALT
  • Black and Decker
  • DeVilbiss
  • Craftsman
This part works with the following products:
  • Angle Grinder
  • Grinder
Part# 611540-00 replaces these:
611540-00,

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

30 - 60 mins 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

on-off slide switch woul not stay latched, had to be held on at all times

PETER from LYONS, New York

3 of 3 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
939539-00, 611737-01, 611540-00, 569624-01
Remove grinder gear head, 4 screws.Remove rear housing 1 screw. disconnect brushes. Pull out rotor and attached fan,diffuser, and bearing. Pull leads out of stator and caps to remove 2 screws. Unplug switch leads, remove switch and switch support, power cord all together. Push stator assembly forward out of housing far enough to get link and button out of housing. Put new link in slot and snap button in end of link through housing opening. Push stator to the rear back onto the housing. Assemble everything back in reverse. Note; When putting rotor in housing make sure the little tabs on fan diffuser are lined up.
Read less
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP10181415
Manufacturer Part Number: 611540-00
Brand Model Number Description
Black and Decker 26436 Angle Grinder - 4-1/2 Small Angle Grinder
DeWALT 26742 Angle Grinder - Angle Grinder
Black and Decker 27326 Angle Grinder - 4-1/2 Small Angle Grinder
Black and Decker 27703 Angle Grinder - 4-1/2 Right Angle Grinder
Black and Decker 27742 Angle Grinder - 4-1/2 Right Angle Grinder
Black and Decker 27743 Angle Grinder - 4-1/2 Right Angle Grinder
Craftsman 900277422 Angle Grinder - Grinder
DeWALT D28090-AR Angle Grinder - 4-1/2" Small Angle Grinde
DeWALT D28090-B2 Grinder - 4-1/2 Small Angle Grinder
DeWALT D28090-B3 Grinder - 4-1/2 Small Angle Grinder
DeWALT D28090-BR Grinder - 4-1/2 Small Angle Grinder
DeWALT D28090AV-B2 Grinder - 4-1/2 Small Angle Grinder
DeWALT D28090AV-B3 Grinder - 4-1/2 Small Angle Grinder
DeWALT DW818 Angle Grinder - Angle Grinder
DeWALT DW818-AR Grinder - 4-1/2 Inch Grinder
DeWALT DW818-B2 Grinder - Slider Sag
DeWALT DW818-B3 Grinder - Slider Sag
DeWALT DW818-BR Grinder - 115mm Grinder
DeWALT DW821 Angle Grinder - Angle Grinder
DeWALT DW824 Angle Grinder - Grinder
DeWALT DW827 Angle Grinder - Grinder
Switch Support
$ 6.16
Special Order
✖
Stock Status
✖
Mail-In Recycling Rebate

Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.

✖