Easy
15-30 minutes
It is a genuine item that is supplied by the original equipment manufacturer for use with Dremel tools. The switch allows a user to control the on-off function of the tool, over time components tend to wear out and they may begin to fail eventually requiring a replacement. Keep in mind this high-quality plastic body part is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item.
On-off Switch 2610912826
OEM part for: Dremel, Bosch
Part Number: 2610912826
$12.83
In Stock
Ships within 1 business day 
Compatibility
This part will fit the following 4 machines
Dremel
215 (F013027506) Corded Multi-Tool View Diagrams & Manuals
275T6 Multipro Multi-Tool View Diagrams & Manuals
100 (F013010001) 100 Series Rotary Tool View Diagrams & Manuals
100 (F013010000) Series Single Speed Bare Tool 100 View Diagrams & Manuals
This item works with the following types of products:
- Multi-Tool Parts
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
ol girl is alive again
my old Dremel needed a switch and these guys had it. looked at several sites and finally arrived here. fair price ,quick ship,it fit perfectly. my Dremel is back to work. would use ereplacmentparts again.
Guest -
April 6, 2022
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for On-off Switch
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Thought (incorrectly) that speed control switch was defective
Michael - December 8, 2018
👍 2 of 2 people found this instruction helpful
Tool Type
MultiTool
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, Torx bit
Parts Used
1. Removed 4 screws and opened clamshell casing.
2. Removed carbon brushes and rubber end cap on rotor.
3. Pulled out two supply wires from speed controller.
4. Removed speed control switch.
5. Installed on/off switch and re-assembled.
6. Discovered device is only ON/OFF; no speed control. Pops GFCI each time I switch off.
7. Removed new switch, replaced old one. Works fine.
8. Complained to erplacecementparts that on/off switch had come up when I was searching for speed controller and I was not aware that their device was not that.
2. Removed carbon brushes and rubber end cap on rotor.
3. Pulled out two supply wires from speed controller.
4. Removed speed control switch.
5. Installed on/off switch and re-assembled.
6. Discovered device is only ON/OFF; no speed control. Pops GFCI each time I switch off.
7. Removed new switch, replaced old one. Works fine.
8. Complained to erplacecementparts that on/off switch had come up when I was searching for speed controller and I was not aware that their device was not that.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The on/off switch had died.
Lori - February 18, 2018
👍 1 of 1 people found this instruction helpful
Tool Type
MultiTool
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, Philips screwdriver
Parts Used
I found a repair video on youtube on how to do the repair. Dremel tools are wonderful and being able to find a youtube repair video is the best help for the DIYer. https://www.youtube.com/results?search_query=dremel+1001+repair
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Brushes and holders wore out
Frank - January 28, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
MultiTool
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
Opened tool
Removed old holder
Cleaned commutator
Plugged in new holder
Installed brushes
Closed tool
Removed old holder
Cleaned commutator
Plugged in new holder
Installed brushes
Closed tool
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Multi tool switch was bad
Hal - March 27, 2020
Tool Type
MultiTool
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, I don\\\'t rmember
Parts Used
80% of any of these "not sure I know how" repair jobs is getting started and Replacemant Parts is the place to go for needed parts and help. The repair of my multi tool went great!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
starter switch wouldn't stay in ON position.
Philip - August 14, 2019
Tool Type
MultiTool
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Wrench Set, wire cutters
Parts Used
Separated case halves.
took out old switch replaced with new one.
Closed both halves of tool
make sure brushes were set and tighten case screws.
took out old switch replaced with new one.
Closed both halves of tool
make sure brushes were set and tighten case screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Dremel would not operate
Stewart - June 22, 2018
Tool Type
MultiTool
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
1. Removed 4 phillips screws holding Dremel together
2. Spun off front retaining collar
3. Removed motor and stator assembly
4. Pulled AC wires from old switch.
5. Removed old switch
6. Reversed order with new switch.
Done.Very easy, glad replacement switch was available, you guys always have the right stuff.
2. Spun off front retaining collar
3. Removed motor and stator assembly
4. Pulled AC wires from old switch.
5. Removed old switch
6. Reversed order with new switch.
Done.Very easy, glad replacement switch was available, you guys always have the right stuff.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Worn out on off switch
Randy - April 26, 2020
👍 0 of 1 people found this instruction helpful
Tool Type
MultiTool
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver
Parts Used
I took apart dremel and replaced the on off switch.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
