Easy
15-30 minutes
This is an authentic replacement part manufactured for use with Milwaukee compact drivers. The motor is a complete assembly including the terminals and pinion gear. This motor is available as an individual replacement part, please see model diagram for associative parts.
Motor Assy Svc 23-30-0095
OEM part for: Milwaukee
Part Number: 23-30-0095
$17.80
In Stock
Order within the next 8 hours and your part ships today! 
Compatibility
This part will fit the following 4 machines
Milwaukee
2401-20 (SER B30A) Compact Driver View Diagrams & Manuals
2401-20 B30B Sub-Compact 1/4" Hex Driver View Diagrams & Manuals
240120 M12 Sub-Compact 1/4" Hex Driver View Diagrams & Manuals
240122 M12 Sub-Compact 1/4" Hex Driver View Diagrams & Manuals
This item works with the following types of products:
- Drill Parts
- Electric Drill Parts
- Cordless Drill Parts
- Impact Driver Parts
This part replaces obsolete part #: 23-30-0095M
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Easy to change
It fit my drill as advertised.
Guest -
April 8, 2023
Verified Purchase
Easy repair
The motor was an exact match and very easy to replace. A little soldering on the positive and negative and it is ready to go.
Guest -
June 26, 2021
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Motor Assy Svc
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Drill motor was seized up
Michael - May 26, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Cordless Drill
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, small star drive screwdriver, solder gun, needle nose pliers
Parts Used
Remove all star screws, there is one longer screw so note the location for reassembly
Remove small clip where battery slides in
Remove 1 half of case
Drive out the 2 retaining pins that secure the motor to the chuck
Unsolder the two motor leads
Install new motor to the chuck add a dab grease to gear
Solder the leads to motor
Reassemble the case
Remove small clip where battery slides in
Remove 1 half of case
Drive out the 2 retaining pins that secure the motor to the chuck
Unsolder the two motor leads
Install new motor to the chuck add a dab grease to gear
Solder the leads to motor
Reassemble the case
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Motor seized up.
Brett - April 27, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Cordless Drill
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Soldering iron
Parts Used
Remove screws on motor housing, pull out motor and unsolder motor. Solder motor connections (look for black next to connections on motor) for black wire placement then reassemble.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Dana - March 7, 2019
Tool Type
Cordless Drill
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Solder gun
Parts Used
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Original motor went up in smoke
George - August 29, 2017
Tool Type
Impact Driver
Difficulty
Easy
Time
15-30 minutes
Tools Used
Pliers, Torx screwdriver bit, soldering iron flux and solder
Parts Used
Remove the screws from the housing and separate carefully
Unsolder the old motor and remove it
Install the new motor and solder the leads on to it
Screw the housing back together
Unsolder the old motor and remove it
Install the new motor and solder the leads on to it
Screw the housing back together
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Motor not working
ron - October 24, 2016
Tool Type
Impact Driver
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Soldering iron
Parts Used
Pulled screws from front, then side, split case, removed innards, unsolder old motor, soldered new motor, reassembled.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
