It is a genuine Bostitch item that is supplied directly from the original equipment manufacturer for use with nailers. This replacement gasket is utilized to provide an air-tight seal between the end cap and the main housing. Seals and gaskets over time tend to wear out and crack eventually requiring replacement to maintain tool's peak performance. It is a high-quality component which is made of durable composite material and it is sold individually.
Gasket,frame/cap 100212
OEM part for: Bostitch
Part Number: 100212
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 4 machines
Bostitch
This item works with the following types of products:
- Nailer Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Gasket,frame/cap
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
orings bad , parts broken and degraded
Tool Type
Nailer
Difficulty
Hard
Time
More than 2 hours
Tools Used
Screwdriver, Wrench Set, wire brushes, pocket knifes
Parts Used
Broken bumper.
Tool Type
Nailer
Difficulty
Easy
Time
15-30 minutes
Tools Used
, Allen wrench
Missing the pins that hold trigger,trigger valve assembly leaking,,,obtained trigger valve assembly locally
Tool Type
Nailer
Difficulty
Easy
Time
15-30 minutes
Tools Used
, metric allen wrench, roll pin punch, curved pointed probe
2. Lubed new trigger valve assembly with air tool grease and inserted valve in body,noting that the grooves on trigger valve assembly lined up with pins that hold it in
3. Using the roll pin punch of correct diameter,drove the pins in that hold the valve assembly and the trigger
4. Remove firing valve and removed the driver, cleaned cylinder, cleaned driver and installed new o ring on driver piston
5.Installed new cap gasket/seal and torqued the four cap screws,,,
6. Loaded nails in roofing nailer and tested it on piece of 2X4,,worked perfect,,very important to install the driver in correct position,,,failure to do so could break the hardened steel driver
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.