This is available as an individual replacement part. The fuel tank on/off valve attaches to the tank and is made out of metal and plastic. A screwdriver, a set of pliers, a socket set, and a wrench set might all be helpful during the installation of this item. Over time this part may cause leaks and will need to be replaced. This genuine item is supplied by the original equipment manufacturer for use with Ariens snow throwers.
Troubleshooting
This part works with the following brands:
Ariens
This part works with the following products:
Snow Blower
Chainsaw
Cultivator
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(2 Reviews)
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ready for snow
The part was easily found,ordered and received
Guest - January 5, 2021
Verified Purchase
★★★★★
★★★★★
As expected
Part was exactly as expected. Could find it elsewhere for slightly less, but the timely service and piece of mind knowing it was likely the correct one was worth shopping here.
Guest - April 12, 2023
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
30 - 60 mins
(7 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
1. Drain the fuel tank of gas.
2. Remove the one 10mm bolt from the dip stick tube.
3. Remove the 5 10mm bolts holding the fuel tank.
4. Unscrew the 2 phillips screws holding the auto start from the fuel tank.
5. Remove the fuel line from the value.
6. Unscrew the shut off value from the tank.
7. Revers
... Read moree the first 6 steps to reassemble.
1. Removed the rope starter assembly and the baffle under the fuel tank in order to access the fuel valve.
2. Drained the fuel tank.
3. Unscrewed the old fuel valve from the bottom of the tank.
4. Installed the supplied screen onto the top of fuel valve and threaded the new valve into the bottom of the tank.
6. Add
... Read moreed fuel to the tank and tested the new valve for leaks. No leaks!
7. Reinstalled the baffle and the rope starter assembly.
8. Filled the fuel tank and test run the machine.
Read less
Did you find this story helpful?
Thank you for voting!
Seals were shot. Leaked fuel like an open valve. Unlike most other fuel on off valve this is a riveted so it can\'t be opened and rebuilt.
Had to remove the metal engine covers to get to the fuel valve, Replaced the fuel valve and line with new ones. Reattached the covers, Problem solved. Machine is like new again. Not very difficult but caution and some mechanical knowledge is helpful and suggested. Parts are a bit delicate and could be damaged if over tightened, forced,or
... Read more roughly handled. eReplacementParts.com was a great source for the part, very easy to deal with and shipped quickly. I will be looking here next time I need any parts for my next repair, I do and will be recommending this site to all.
Turned gas valve to \"off\" position
Removed covers (10mm hex head bolts) from shutoff valve area
Disconnected gas line to carburetor
Connected short separate poly tube to gas valve to drain gas tank into gas can
Opened gas valve to drain tank
When drained, remove temporary hose
Unscrewed leaky valve fr
... Read moreom bottom of tank
Applied thread sealant to threads on new valve
Screwed valve into bottom of tank
Tightened lock nut - taking care to not make too tight, which would damage the gasket on the threaded valve section
Reconnected gas hose to carburetor, reattached covers.
DONE
1. Dumped fuel out of gas tank.
2. Removed housing bolts.
3. Removed fuel lines.
4. Used wrench to remove old fuel valve then unscrewed in tank fuel filter with fingers
5. Installed new in tank fuel filter on new fuel valve and installed the new valve on the gas tank.
6. Put new gas in tank, made sure no leak
... Read mores, and started it up.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP11834432
Manufacturer Part Number: 20001436
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
