Genuine Husqvarna replacement part, this item is sold individually. The purpose of the Fuel Tank Bushing is to create a seal and prevent leaks from the fuel tank. The fuel line are inserted in to the Bushing. It is then pressed into the holes provided in the fuel tank.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy repair. Correct part the first time
Great condition, correct part
Guest - July 8, 2019
Verified Purchase
★★★★★
★★★★★
quality part
fit great.
Guest - September 23, 2020
Verified Purchase
★★★★★
★★★★★
Price, availability, service, & speedy delivery!
I contacted local husquavarna dealers that had not gotten parts order deliveries in 2.5 months! Eplacementparts had all my parts in stock for a decent price! Knowledgeable service gal shipped them right out! Fixed my chainsaw easily without paying a $100 an hour mechanic who was booked out 1 month! I'll remember to return to this site 1st next time.
Guest - January 18, 2022
Verified Purchase
★★★★★
★★★★★
Fast
Always quick service.
Guest - February 9, 2023
Verified Purchase
★★★★★
★★★★★
FIT PERFECTLY
Install was easy and the parts were excellent quality.
Guest - April 16, 2023
Verified Purchase
★★★★★
★★★★★
Worked as expected!
The part was exactly what we were looking for, easy to find! Now our trimmer is working again!!
Guest - June 13, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Remove chain and bar( for easy maneuverability), empty gas in tank, then top cover, followed by handle and throttle grip. The throttle has to be disconnected from carb, and you have to spin the linkage to remove because it does not come straight out.
2. You can choose to remove carb, I was able to do repair without removing, prob
... Read moreably more difficult, but might have saved a little time. I removed return line and fuel lines and prime bulb from saw, followed by grommets. To remove fuel line you have to open gas tank and pull out filter and fuel line with your 90 degree pick. Remove filter and hose, replace with new.
3. When I replaced grommets and hose, I put a little oil on them to make things go on a little easier. I found it is easier to install grommets on hose first and then install grommets on saw. You can always push and pull hose through.
4. Once all hoses are on and secure, reinstall your filter on line and replace inside tank. I cut about two inches off the tank line before installing filter, just because it seemed a little long, your choice. I only had one line that was bad, but I figured while I was replacing one, might as well do them all, the others are probably going to fail soon.
5. In order to replace exhaust screen, you will have to remove chain break handle, two hex head bolts, slide screen out, slide new one in and done.
6. Once installed, I reassembled everything in the reverse order it come out. Chain brake handle, main handle then throttle cover, remember to install throttle linkage, you have to spin it to get back next to the carb, this can be a little tedious, but make sure it is where it needs to go before bolting main handle on, or you have to take it apart again(my mistake).
7. After throttle cover, replace your top cover, and chain and bar, add gas and your good to go.
Read less
Did you find this story helpful?
Thank you for voting!
Was leaking fuel around the fuel lines that go from the gas tank to the carb.
1 removed outside plastic covers
2. Removed dirt and fuel from around the motor.
3 removed fuel tank
4 removed old fuel lines and grommets from gas tank
5 replaced fuel lines and grommets Be clean entire trimmer.
6 hooked fuel tank back up attached plastic covers.
7 filled fuel tank and checked for lea
... Read moreks and started trimmer. Everything works great just like new.
1. Removed engine cover.
2. Removed fuel tank
3. Replaced fuel line and return line
4. Put new fuel filter in tank
5. Replaced tank and cover
6. Installed new spark plug and air filter started right up
Removed gas line and determined it was plugged - also had small crack
Replaced gas line, fuel tank bushing and bellows
To reinstall bushing, remove two rear shock bushings holding gas tank to engine body - this gives you more space to work bushing into tank opening without damaging it.
Run fuel line under kill switch wir
... Read moree and under choke connector
Read less
Did you find this story helpful?
Thank you for voting!
hose/tank grommets leaked when trimmer tilted during operation
Removed covers including recoil starter assy.
Removed fuel tank, disconnecting fuel lines.
drained/emptied fuel tank.
Removed priming bulb and fuel lines.
Removed fuel lines and grommets from fuel tank.
Installed new grommets in tank.
installed new lines in tank.
installed new lines to priming bul
... Read moreb.
installed priming bulb and lines.
connected lines to carb.
reinstalled tank.
reinstalled covers and recoil starter assy.
checked all connections and retightened all screws.
fueled the unit.
Started unit checking for leaks, none found.
trimmer ops ck satis.
Read less
Did you find this story helpful?
Thank you for voting!
fuel lines and air purge old and brittle (\'09) Husqvarna 223L Trimmer
Removed starter assy housing ( 3allen screws ) just for easier accessability , removed top cover ( 1 allen screw ) - took picture of three fuel lines (routing) - simply removed and replaced all above items mentioned . RUNS GREAT ! Cheaper than buying a new trimmer !
Did you find this story helpful?
Thank you for voting!
Fuel tank bushing was leaking and fuel line had wore out
1. I examined the fuel leak and determined that the fuel line and bushing was leaking.
2. I removed the fuel filter, and then removed the fuel line with a pair of needle nose pliers.
3. Then with the needle nose pliers I placed the bushing in the hole on the top of the fuel tank, and then placed the fuel line in the bushing as
... Read more far as what was needed to attach the fuel line to the carburetor, the other end I pulled out of the fuel tank fuel hole and attached the new fuel filter.
Removed plastic protective cover to expose fuel tank. Removed tank screws and replaced bushing and fuel line while I was at it. No issues and fairly easy repair. This was on a Husqvarna pole saw. 326P5X
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP11824288
Manufacturer Part Number: 580457501
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
