Easy
15-30 minutes
It is an authentic OEM component which is made for Hitachi nailers. This spring applies tension on the feeder piece which helps to supply nails from the magazine to the tool. If the spring is stretched, damaged or lost, this part will provide an identical replacement for the original hardware that was installed on a new unit. One durable metal feed spring is included. Replacing it is a simple task that should only require a screwdriver. Check the appropriate diagrams for your model to ensure the proper repair procedure.
Feed Spring 885900
OEM part for: Metabo HPT (Hitachi)
Part Number: 885900
$5.19
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 10 machines
Metabo HPT (Hitachi)
NT50AE2 2" 18-Gauge Brad Nailer View Diagrams & Manuals
NT32AE2 Brad Nailer View Diagrams & Manuals
NT50AE2(S) Brad Nailer View Diagrams & Manuals
NT50GS Gas Finish Nailer View Diagrams & Manuals
NT1850DESM 18v Brushless Li-Ion 18-Gauge Straight Brad Nailer (3.0cah X 1) View Diagrams & Manuals
NT1850DESQ7M 18v Brushless Li-Ion 18-Gauge Straight Brad Nailer (Bare) View Diagrams & Manuals
NT50A5M 2 Inch18ga Brad Nailer Pro 2 Inch View Diagrams & Manuals
NT1850DE Nailer View Diagrams & Manuals
NT50A5 Nailer View Diagrams & Manuals
NT50GSP9 Nailer View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Nailer Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Feed Spring
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
The nail magazine broke a small piece of the track. This allowed the nail feeder to slide out of the magazine. The spring then comically shot the parts across the room.
Jason - February 3, 2021
Tool Type
Nailer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, Allen wrench
1 remove magazine from nailer
2 removed socket head cap screw from retainer
3 slid new sprin into the new magazine
4 slid new nail plate onto spring with the connector
5 while holding nail plate back replaced retainer on magazine
6 tested spring and feeder
7 shot some nails
2 removed socket head cap screw from retainer
3 slid new sprin into the new magazine
4 slid new nail plate onto spring with the connector
5 while holding nail plate back replaced retainer on magazine
6 tested spring and feeder
7 shot some nails
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Nail feeder and feeder piece were gone and spring was bent.
Moe - June 1, 2020
Tool Type
Nailer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, A pocket knife
Pushed spring in and held with knife tip
Put yellow plunger on spring
Placed nail feeder in plunger.
Took latch piece loose and inserted assembly into gun.
Replaced latch piece.
It was done.
Ta Da
Put yellow plunger on spring
Placed nail feeder in plunger.
Took latch piece loose and inserted assembly into gun.
Replaced latch piece.
It was done.
Ta Da
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air nailer leaked air thru top of gun
James - August 11, 2017
Tool Type
Nailer
Difficulty
Easy
Time
30-60 minutes
Tools Used
Pliers, allen wrench set
1. Removed exhaust cover and head cap
2. Removed cylinder and cleaned out housing
3. Replaced O-rings, exhaust valve, and head cap
4. Reassembled nailer
2. Removed cylinder and cleaned out housing
3. Replaced O-rings, exhaust valve, and head cap
4. Reassembled nailer
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Nails didn't feed
John - February 10, 2016
Tool Type
Nailer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, 4mm hex driver
Remove screw holding bottom of magazine, remove magazine, insert spring and plate replace magazine screw.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
