eReplacementParts.com
877-346-4814
Poulan Parts
Preferred Partners of
photo thumbnailphoto thumbnail360 degree photo thumbnail

Cylinder

Part Number: 530012541
PoulanWeed EaterHusqvarna
Availability: 12 in stock
Price: $20.34
Ships within 1 business day
Product Information
Manufacturer: Poulan, Weed Eater, Husqvarna
Product Number: 530012541
Classification: Part
Weight: 0.63 lbs.
Shipping: Ships Worldwide
Description:
This is an original replacement part manufactured for outdoor power equipment. The cylinder is used to house the piston and spark plug and is used to provide a combustion chamber to ignite the air-fuel mixture. This cylinder is available as an individual replacement part, please see model diagram for associative parts.
Frequently Purchased With
Compatibility

This part is compatible with the following machines:

Poulan
Weed Eater
Husqvarna
Expand the 111 compatible machines
Products Compatibility

This item works with the following types of products:

  • • Blower
  • • Edger
  • • Pruner
  • • Trimmer
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
3 of 3 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Cylinder - 530012541
Gasket Kit - 530071750
Air Box - 580731001
Kit- Piston - 530071833
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Pliers
Hard starting, lack of power, adjusting carburetor made no difference.
1. Removed shrouds
2. Removed engine from trimmer mount
3. Removed cylinder from block
4. Removed retaining rings from piston, pushed piston pin out, removed piston.
5. Reversed above procedure installing new piston
6. Installed piston ring, oiled piston and ring, then slid cylinder over piston
7. Bolt cylinder down
8. Remove accessories from first cylinder and install on new cylinder
9. Reinstall engine on trimmer mount, reinstall shrouds
10. Start engine and adjust carburetor
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Fuel Cap With Retainer - 530014347
Spark Plug - 952030249
Cylinder - 530012541
Kit - Piston/Rod - 530071785
O-Ring - Rear Plug Kit - 545180866
Repair Difficulty:
Easy
Time Spent Repairing:
1-2 hours
Tools Used:
Socket set, Wrench Set, Nutdriver, Torx set
No compression, damaged cylinder.
Disassemble the blower/engine down to the crankcase, clean as needed, install new piston kit and cylinder, reassemble blower and test run.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Cylinder - 530012541
Piston Ring - 545154001
Flywheel Assembly - 545221701
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Torx bits and allen wrenches
No start.......no attempt to start even with starting fluid. Compression was at minimums when I checked it.
Unit will have to be completely disassembled so remember (i.e. take pictures) as you go. Remove carb. and fuel tank at the same time and leave hose hooked to carb. Got to the other side and remove plastic cover over exhaust muffler and remove muffler, gasket and metal deflector. Remove carrying handle (2 screws) and the top plastic cover. At this time you can remove spark plug if you desire...........or you can wait until later.
Bottom side of unit............remove 3 screws covering and protecting fan and set cover and screw aside. Hold fan and remove nut, lock washer and large flat washer. Set this aside also. Remove fan duct and nozzle (4 screws) and set it aside. Now all that is left is the lower housing (4 screws) Remove screws and housing and set aside.
Flywheel is exposed at this point and (in this order) you will find a space and washer (washer is next to flywheel. Remove them and set aside. Gently work flywheel back and forth.......a little lubricant between shaft and flywheel will help. Shaft is tapered so it will come off with a little effort.
Next I took the two allen head bolts holding the cylinder head on. Set them aside and remove head. I removed the piston and rod assembly due to over-heating and or lack of proper lubricant in fuel. To remove the assembly the "black" cover (2 screws) on rear if engine block will have to be removed.
To reassemble everything is reverse from disassembly. I used RED Loctite on the cylinder bolts and BLUE Loctite on the Fan Nut and shaft.
Main culprit I found was the piston ring was frozen to the piston and the cylinder was scored. Compression was dismal and what I suspected was proven once the unit was disassemble.
Make sure you have a good supply or Torx screwdrivers and bits (various sizes) along with a good Allen Wrench set
Don't forget to watch for the gasket behind carb. It will come lose and may wind up on the floor when you remove the carb. Same goes for the exhaust.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Trimmer
Parts Used:
Cylinder - 530012541
Piston Ring - 545154001
Repair Difficulty:
Expert
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, Piston stop that screws into sp plug hole. Clutch removal to
After 4 years of service, trimmer would not run, low compression
Disassembled trimmer engine. Installed new cylinder and ring. Compression restored. Carb rebuild kit also installed. Trimmer now runs good with good power. I enjoy repairing equipment.

I ordered a piston stop special tool. Screws into the spark plug hole to stop the engine from rotating when removing the centrifugal clutch to disassemble the unit. Ordered a clutch removal special tool.

I was very impressed with the quality of the entire power equipment business. High quality products. Good replacement parts online service. Very good online illustrations. Good prices and shipping time. Excellent support including YouTube videos.
I
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Cylinder - 530012541
Kit- Piston - 530071833
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Socket set, 6mm -1,oo Tap 5mm-0,8tap
running without mix fuel
Set out cylinder and piston get parts from you, but no thread at the cylinder I bout Tap set ,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Cylinder - 530012541
Piston Ring - 545154001
O-Ring - Rear Plug Kit - 545180866
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, None
Piston rings frozen and cylinder scored.
Disassembled blower and removed cylinder and piston. Cleaned piston and other parts. Replaced parts and reassembled blower.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Trimmer
Parts Used:
Cylinder - 530012541
Kit- Piston - 530071833
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Allen and torch wrenches
Low compression
Removed old cylinder and piston. Replaced with new parts. Reassembled. Runs great.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Cylinder - 530012541
Piston Ring - 545154001
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
, allen wrench
no compression
Total tear down to cylinder and piston. Had a scored cylinder and a stuck piston ring, which scored the cylinder. Replaced cylinder and cleaned groove for new piston ring, reassembled and fired right up. Had to adjust the carb jets to tune low and high rpm settings. Removing the cylinder was challenging, due to allen head bolts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5
Average Rating (out of 5):
3 Reviews
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • THE CYLINDER HEAD
    THIS CYLINDER HEAD WAS A PERFECT MATCH, I WAS EASY TO INSTALL. MY LEAF BLOWER RUNS LIKE A NEW ONE, THANKS FOR ALL YOUR HELP.
    Guest - August 11, 2021 Verified Purchase
    Exactly what I needed
    Ereplacementparts has always had the parts I’m looking for! The website is great and is easy to use to look up and find what I need. Shipping is fast! Love this site!!!
    Raymond - November 26, 2019 Verified Purchase
    Good part, good seller
    Good part and fast delivery
    iGlobal - October 8, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Poulan, Weed Eater, Husqvarna
    Product Number: 530012541
    Classification: Part
    Weight: 0.63 lbs.
    Shipping: Ships Worldwide

    Fixing things makes sense...

    ...And we make it easy! With our Fix app, you always have a personalized repair guide on-hand. Easily find manuals and replacement parts on your phone while you’re DIYing in the garage or garden.

    "Love the flexibility of the app to add everything in the home and garage. Access to manuals and parts right there makes it convenient."

    Available on the App Store Get it on Google Play
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal