866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  HVAC Parts  Heatstar Parts  60105 Circuit Board

Circuit Board

Part Number: 60105
HeatstarMr. Heater
Availability: 10 in stock
Price: $68.40
Quantity:
Order within the next 11 hours
and your part ships today!
Description:
This manufacturer-supplied replacement part is designed for use with Heatstar and Mr. Heater compact unit heaters. The circuit board helps to control the unit. It provides an identical replacement for a missing or a faulty component that was installed on a new unit. Please refer to the appropriate diagrams of your model for the exact location and the correct installation of this part. Keep in mind this high-quality circuit board is sold individually. You will need a screwdriver to take apart the housing in order to gain access to the circuit board.
Product Information
Manufacturer: Heatstar, Mr. Heater
Product Number: 60105
Classification: Part
Weight: 0.65 lbs.
Shipping: Ships Worldwide
Compatibility

This part is compatible with the following machines:


Products Compatibility

This item works with the following types of products:

  • • Heater
Questions & Answers

3 amp fuse keeps blowing on mr heater big maxx. no apparent bad spots on board and all wires look good. Bad Board?
robert
Hello Robert, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
The new igniter will still not glow and ignite. Is it circuit board?
Bob for model number MHU75
Hello Bob, Thank you for the question. If the igniter did not fix the issue, the next likely cause would be a defective board. Hope this helps, good luck with this repair!
Will this circuit board work for mhu50 propane the part number is the same in the manual 60150 Thanks Mike
Mike for model number Mhu50
Hi Mike, thank you for your question. This part is the correct part for your heater. Good luck with your repair.
Repair Instructions: Submitted by Customers Like You
10 of 11 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Power Drill
Board would not produce a spark to ignite gas.
Pull old board out, then install the new board then wire for wire exchange.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
7 of 7 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set, Nutdriver
I have a 2008 75000btu big max Mr heater. The problem was, the fan would cycle on, gas valve would open but the igniter would not ignite.
My heater is hung in the corner with cabinets on both sides. This made it more difficult, but not impossible. I ordered a control board I removed wires from the old board and plugged into the new board. Then I unscrewed the old board, and removed, and then installed the new board. Turned the power on and everything worked. Been running for a week now and no problems. I am glad it was the board because the igniter looks like it would have been worse.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
4 of 4 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Nutdriver, Adjustable Wrench
Replaced bad circuit board
Remove right access panel then replace circuit board. Replace one wire at a time.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Nutdriver
The igniter circuits had failed on both of my Mr. Heater ceiling mounted propane heaters in my shop.
My shop has a high ceiling (14' at the eaves) so I had to perform the repair while on a 15" fruit ladder. It is very straightforward: Disconnect power; remove the side cover; remove the four sheet metal screws that hold the circuit boards at the corners; swap the wires to the new board; secure the new boards with provided screws and spacers; replace the side cover; restore power --- and they worked perfectly!

The original boards had 3/8" spacers to allow air flow between the circuit boards and the sheet metal to which they are attached. That metal separates the burner from electrical assemblies in the heater. The boards from eReplacementParts had 1" spacers that may allow the boards to last longer. Put the new, longer screws through their respective holes, wrap with one wrap of electrical tape, and slide the 1" nylon spacers over the tape. That will hold the spacers in place until you are ready to secure the board to the furnace.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set
Circuit board had intermittent problem that prevented the burner from lighting.
Turned off power to the heater. Disconnected the wiring to the circuit board being careful to insure where they came from. Removed the mounting screws. Reinstalled the new circuit board using the new stand off parts and screws. Reconnected the wiring connectors. Turned on power to the heater and then adjusted the thermostat to call for heat. The unit then went through its start up functions and the burner lit. All has been well since.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Bad Circuit Board
Replace the board as directed and exchanged wire for wire and it works like a champ. With no issues.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Heater wound not ignite, master board was not working
removed old board, installed new board works great
easy install, take wires off old board-install wires on same terminals on new board
Disconnect Power Source Before Starting Procudure !
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Nutdriver, Long Needle nose pliers
No spark when heater tried to start
Exchanged control board.
The hardest part was the mounting screws are not held in place in the mounts like to old one.
A long needle nose pliers was needed to hold the mounts behind the board for the bolts to be started,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Electrode Igniter - 60729
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Heater
Parts Used:
Circuit Board - 60105
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Old controller was burnt replaced with new
Removed old unit swapped wires to new and re-installed
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5
Average Rating (out of 5):
1 Reviews
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Worked just like the factory part!
    Was easy to install and fixed my problem! Thank you in frozen Minnesota!
    Richard - April 18, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    visa mastercard discover american express PayPal
    HACKER SAFE certified sites prevent over 99.9% of hacker crime.

    fancyboxy