eReplacementParts.com
866-322-9842
DeWALT Parts
Repair Parts Home  Power Tool Parts  DeWALT Parts  392574-01 Carbon Brush With Wire Lead

Carbon Brush With Wire Lead

Part Number: 392574-01
DeWALT
Availability: 25+ in stock
Price: $8.98
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: and 392460-01.

Product Information
Manufacturer: DeWALT
Product Number: 392574-01
Classification: Part
Weight: 0.01 lbs.
Also Known As: Motor Brush With Wire Lead
Shipping: Ships Worldwide
Description:
Genuine DeWalt replacement part
Includes 1 Carbon Brush with wire lead attached.

• Worn brushes frequently are the cause behind a motor running poorly.
• Replacing brushes can fix a motor that’s operating intermittently.
• New brushes can restore a motor’s electric braking.


Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Products Compatibility

This item works with the following types of products:

  • • Chop Saw
  • • Grinder
  • • Sander
  • • Saw
Questions & Answers

what are the dimensions (H x W x L). I think I need: 6.2 mm x 16 mm x 26.5 mm Also, do you have free shipment with certain minimum order?
Dean
Hi Dean, Thank you for your questions. The dimensions for this part are 32 mm by 22 mm by 22 mm. Also, we do not provide free shipping with a minimum order. I hope this helps. Thank you and have a great day!
Repair Instructions: Submitted by Customers Like You
2 of 3 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Carbon Brush With Wire Lead - 392574-01
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Grinder would not run
Removed the rear handle and cover, pulled spring back holding the brush in the brush holder, disconnected the brushes from holders, then connected the new brushes, inserted the brush in the holder, then put the springs back in place. Then I attached the rear handle and cover.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush With Wire Lead - 392574-01
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, TORX T20 DRIVER
CARBON BRUSH WENT BAD.
REMOVE BRUSH COVER WITH T20 DRIVER MOVE SPRING, UNPLUG BRUSH LEED WIRE REMOVE BRUSH PLACE NEW BRUSH IN THE SAME WAY YOU REMOVE THE OLD ONE, PLUG IN THE LEED WIRE AND SET SPRING BACK ON TOP OF BRUSH. REPLACE COVER . DONE.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush With Wire Lead - 392574-01
Switch - 394375-04
Brush Spring - 623589-00
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Brushes wore out in corrosive environment.
Unscrewed body and removed brushes with needle nose pliers.
Cleaned out. replaced brushes and holders and new springs.
Then reassembled body.
No special requirements just pay attention to the tear down and reverse procedure.
Note: be careful unplugging wire connections.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Carbon Brush With Wire Lead - 392574-01
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes were worn out
Removed both sides of the rear housing
Pull back the spring hold the brushes in and place the end of the sprig on the brush holder
Disconnect the old brushes and removed them
Install the new brushes and connect them
Release the brush holder spring
Attach both sides of the rear housing
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Carbon Brush With Wire Lead - 392574-01
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Socket set
Worn out brushes.
Removed the old brushes and replaced with the new ones.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5
Average Rating (out of 5):
1 Reviews
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • maintenance
    all the parts I order from u guys always works great and u guys always have the parts I need
    steve - May 29, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: DeWALT
    Product Number: 392574-01
    Classification: Part
    Weight: 0.01 lbs.
    Also Known As: Motor Brush With Wire Lead
    Shipping: Ships Worldwide
    Related Products
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal

    fancyboxy