Manufacturer: Hitachi |
Product Number: 999-043 |
Classification: Part |
Weight: 0.03 lbs. |
Also Known As: Motor Brush Set |
Shipping: Ships Worldwide |
This is a genuine Hitachi replacement part, they are sold as a pair (2). Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor’s electric braking
A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem. |
This part is compatible with the following machines:
WR22SA 3/4" Impact Wrench
VB16Y Grade 60 EVS Rebar Cutter / Bender
C8FB2 8-1/2" Twin Rail Sliding Compound Miter Saw
C8FB2 8-1/2" Twin Rail Sliding Compound Miter Saw
CR13V 10 Amp Reciprocating Saw
CR13V 10 Amp Reciprocating Saw
CR13VA Electric Variable Speed Reciprocating Saw
CR13VA Electric Variable Speed Reciprocating Saw
CR13VBY 12 Amp Low Vibration UVP Reciprocating Saw
CR13VBY 12 Amp Low Vibration UVP Reciprocating Saw
KM12VC 2-1/4HP Variable Speed Fixed/Plunge Base Router
M12VC 2-1/4HP Variable Speed Fixed Base Router
S18SB 7" Vertical Sander
SP18VAH 7" Disc Sander/Polisher
SP18VAH 7" Disc Sander/Polisher
SB8V2 3" x 21" Variable Speed Belt Sander
M12SC 2-1/4HP Single Speed Fixed Base Router
KM12SC 2-1/4HP Single Speed Fixed/Plunge Base Router
SB75 3" 2-speed Belt Sander
SB10T 2-speed Belt Sander
SP18SA 7" Polisher
SAT180 7" 2-Speed Disc Sander/Polisher
SAT180 7" 2-Speed Disc Sander/Polisher
S18SA 7" Sander
WH22 3/4" 10 Amp Square Drive Impact Wrench
C10FS Slide Compound Saw
C8FB Slide Compound Saw
C7SA Circular Saw
C7SA Circular Saw
C7SC Circular Saw
C7SC Circular Saw
CR12V Reciprocating Saw
CR13VB Reciprocating Saw
CR13VB Reciprocating Saw
CR13VC Reciprocating Saw
CR13VC Reciprocating Saw
D13Y 1/2" Right Angle Drill 6.2A
F-30A Electric Planer
G13SC 5" Disc Grinder 9.6Amp
H30PV Hammer
M8 Router
M8V 1/4" Router 1-1/2HP 7.3Amp Electronic Variable Speed
SP18V 7" Electric Disc Sander Polisher
SP18V 7" Electric Disc Sander Polisher
SP18VA 7" Electric Disc Sander Polisher
SP18VA 7" Electric Disc Sander Polisher
TR8 Router
VB13Y 1/2 Motorized Rebar Cutter/Bender
WH22SA Impact Wrench
CR13V2 Reciprocating Saw
CR13V2 Reciprocating Saw
DH38MS Rotary Hammer
DH38YE2 Rotary Hammer
C7ST Circular Saw
C7ST Circular Saw
DH28PC Rotary Hammer
DH28PD Rotary Hammer
H41MB Hammer Drill
H41MB Hammer Drill
G13SC2 Disc Grinder
C10FSH Slide Compound Saw
C10FSB Slide Compound Saw
Remove the old brushes
Installed the new brushes
Replace the brush caps
Removed the side cover
Disconnected the wires from the old switch
Connected the wires to the new switch
Replaced the side cover
Pressed in the lock button
Inserted the new ones and replaced the caps
2 Unscrew the brush caps
3 Take the old brushes out
4 Took the new brushes out of the package and made the repair.
5 Plugged the saw back in.
Took all but 5 minutes for repair.
Note: The outer end of the brushes need to be aliened into their slots in the holders before you try to screw on the brush caps.
As the new brushes wear in you may get better braking. keep it clean and out of the weather and use the dust bag.
- 1
- 2
- 1
- 2
Manufacturer: Hitachi |
Product Number: 999-043 |
Classification: Part |
Weight: 0.03 lbs. |
Also Known As: Motor Brush Set |
Shipping: Ships Worldwide |