eReplacementParts.com
877-346-4814
Milwaukee Parts
Repair Parts Home
  
Power Tool Parts
  
Milwaukee Parts
  22-22-1560 Carbon Brush Assembly

Carbon Brush Assembly 22-22-1560

OEM part for: Milwaukee

Part Number: 22-22-1560


Install
Videos!
Grid squares measure 1x1 inch
In Stock
Ships within 1 business day
Easy Less than 15 minutes (7 rated repairs)?
OEM: Original Equipment Manufacturer ?
Milwaukee
Does this d-block d-md-none fit my product?

Product Description ?

This is a genuine Milwaukee replacement part, it is sold individually.
It includes the brush, brush holder and brush spring.

• Worn brushes frequently are the cause behind a motor running poorly.
• Replacing brushes can fix a motor that’s operating intermittently.
• New brushes can restore a motor’s electric braking.


Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

  • Classification: Part
  • Weight: 0.01 lbs.
  • Also Known As: Motor Brush Assembly
  • Shipping: Ships Worldwide

Frequently Purchased Together ?

Compatibility

This part will fit the following 18 machines

Milwaukee

6140-33 (SER B70A) 4.5" Angle Grinder with Slide Switch View Diagrams & Manuals
6140-30 (SER B69A) 4.5" Angle Grinder with Paddle Switch w/Lock-Off View Diagrams & Manuals
6148-30 (SER B71A) 4.5" Angle Grinder View Diagrams & Manuals
6122-31 (SER B66A) 4.5" Rat-Tail Angle Grinder View Diagrams & Manuals
6148-31 (SER B72A) 4.5" Angle Grinder With Paddle Switch View Diagrams & Manuals
6148-33 (SER B73A) 4.5" Angle Grinder With Slide Switch View Diagrams & Manuals
6116-30 (SER B62A) 4.5" Angle Grinder With Paddle Switch W/Lock-Off View Diagrams & Manuals
6116-31 (SER B63A) 4.5" Angle Grinder With Paddle Switch View Diagrams & Manuals
6116-33 (SER B64A) 5" Angle Grinder With Slide Switch View Diagrams & Manuals
6160-33 (SER B76A) 6" Angle Grinder With Slide Switch View Diagrams & Manuals
6160-30 (SER B74A) 6" Angle Grinder With Paddle Switch W/Lock-Off View Diagrams & Manuals
6160-31 (SER B75A) 6" Angle Grinder With Paddle Switch View Diagrams & Manuals
6123-30 (SER B67A) 6" Rat-Tail Angle Grinder With Lock View Diagrams & Manuals
6123-31 (SER B68A) 6" Rat-Tail Angle Grinder View Diagrams & Manuals
6122-30 (B65A) Grinder View Diagrams & Manuals
0240-20 (C32A) 3/8" (10Mm) View Diagrams & Manuals
6148-30 (B71B) 4.5" Angle Grinder View Diagrams & Manuals
6148-30 (B71C) 4.5" Angle Grinder View Diagrams & Manuals
Show More Compatible Models
Don't see yours? Try searching our site for :

This item works with the following types of products:

  • Grinder Parts
  • Drill Parts
  • Electric Drill Parts

Repair Videos ?

Watch the Repair Video for Carbon Brush Assembly
Articles:
If you own a power drill, you will probably replace the brushes several times during its life. This article shows you ho...
December 20, 2011

Customer Part Reviews ?

4.2
Average Rating (out of 5):
5 Reviews
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 stars
1
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Great Job guys!
    The parts came quickly and were the correct parts. It was a quick swap out and I was back in business. Thanks!
    Guest - March 30, 2020 Verified Purchase
    turned these over to my husband; he says everything is working great.
    Happy with the whole transaction.
    Guest - January 22, 2020 Verified Purchase
    Easy repair
    Received in great shape and grinder works well
    Guest - October 14, 2019 Verified Purchase
    Esy to order parts from.
    Good Quality parts, timely delivery, good customer support
    Guest - August 20, 2019 Verified Purchase
    You can do better Ereplacmetparts
    I ordered replacement brushes for an angle grinder when they showed up one package had the correct holder just no carbon brush. Still waiting for a new on
    Guest - May 26, 2020 Verified Purchase
    t
    t
    t - t days ago Verified Purchase
    eReplacementParts Team
    t

    Questions & Answers ?

    Our customer Service team is at the ready daily to answer your part and product questions.

    photo of team member
    Ask our Team

    We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    Does this fit my product?

    Questions & Answers for Carbon Brush Assembly


    No questions have been asked yet

    Customer Repair Instructions ?

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

    Easy Less than 15 minutes (7 rated repairs)?

    Brushes went bad

    Jason - February 16, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Electric Drill

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Removed the outer cover and replaced brushes put outer cover back on tested drill worked fine
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Sparks, then wouldn't turn on.

    rufus - October 23, 2016
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Grinder

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    , Torx driver

    Removed the rear handle assembly. Then removed the old brushes and installed the new brushes. Screwed the rear handle assembly back on.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Dropped drill, it cracked a carbon brush causing the attached wire to break off

    Michael - February 22, 2023
    Tool Type

    Electric Drill

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    , Star tip driver

    Opened drill case, disconnected ground wire on brush, pulled brush assembly out, installed new brush assembly, reconnected ground wire, reinstalled case,
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Drill wouldn’t run.

    Raymond - December 26, 2021
    Tool Type

    Electric Drill

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver, Pliers, Contact cleaner.

    Open the case at the back, unplug the wire and pull the brush assembly out. Clean the armature with contact cleaner or a pencil eraser, push the new brush assemblies in place and plug the wire back in. Replace the cover and screws. Worked perfectly without any sparking.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    power tru switch but moter wouldn't turn

    Jayson - August 27, 2021
    Tool Type

    Grinder

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    , torx

    1. removed side covers . 2. remove brush wires and brushes . 3 install new brushes and side covers .
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brushes were warn down

    Guy - October 11, 2016
    Tool Type

    Grinder

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Pliers

    1. Removed the three screws and the cover plate
    2. Removed one brush and replaced
    3. Then removed the other brush and replaced it
    4. Replaced the cover plate and screws
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Worn brushes

    robert - June 1, 2016
    Tool Type

    Grinder

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Needle nose pliers

    Remove rear handle assembly from the grinder. Go slow and look how the internal parts are located in the handle. Then remove the terminals from the old brush assemblies. Remove the old brush assemblies and replace them with the new ones, and place the terminals on the new brush assemblies. Then put the handle back together.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.

    Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.

    Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.

    All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.

    This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.

    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal