We Sell Only Genuine Campbell Hausfeld® Parts.
Campbell Hausfeld Pump Parts & Models
Popular Campbell Hausfeld Pump Parts
Genuine Campbell Hausfeld replacement part, this item is sold individually.
When you use a compressor the air that is compressed inside the tank will condensate and leave water inside the tank.
If it is left in the tank too long it can start to rust out the inside of the tank.
The Drain Valve should be opened up and let the water drain out.
The water will build up if you have a tendency to leave air in your tank for a long period of time.
You should drain your tank after each time it is used to prevent this from happening.
The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.
Genuine Campbell Hausfeld replacement part, this item is sold individually.
The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below.
Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air.
The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.
Genuine Campbell Hausfeld replacement part, this item is sold individually.
The Ferrule in this case is used on all of the compressors listed below.
It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor.
It aids in stopping air leaks.
Genuine Manufacturer Approved replacement part designed for use with some Campbell Hausfeld Pressure Washers. This part is made out of Plastic and it is Sold Individually. This Adapter connects to the Pump allowing to for the water flow.
This is a manufacturer sourced replacement pump assembly designed for use with Campbell Hausfeld air compressors. The purpose of the pump is to create pressure to in the air tank. This is a two (2) cylinder, cast iron pump. It is sold individually.
You would need a wrench set to replace this pump.
• Make sure the unit is unplugged
• Disconnect tubes, belt, flywheel and pulley from the old pump
• Remove screws from the base which secure pump
• Remove old pump and secure new one using screws
• Reattach tubes, flywheel, pulley and belt
• Test the new pump
Genuine Campbell Hausfeld replacement part, this item is sold individually.
When you use a compressor the air that is compressed inside the tank will condensate and leave water inside the tank.
If it is left in the tank too long it can start to rust out the inside of the tank.
The Drain Valve should be opened up and let the water drain out.
The water will build up if you have a tendency to leave air in your tank for a long period of time.
You should drain your tank after each time it is used to prevent this from happening.
The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.
Genuine Campbell Hausfeld replacement part, this item is sold individually.
The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below.
Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air.
The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.
Genuine Campbell Hausfeld replacement part, this item is sold individually.
The Ferrule in this case is used on all of the compressors listed below.
It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor.
It aids in stopping air leaks.
Genuine Manufacturer Approved replacement part designed for use with some Campbell Hausfeld Pressure Washers. This part is made out of Plastic and it is Sold Individually. This Adapter connects to the Pump allowing to for the water flow.
This is a manufacturer sourced replacement pump assembly designed for use with Campbell Hausfeld air compressors. The purpose of the pump is to create pressure to in the air tank. This is a two (2) cylinder, cast iron pump. It is sold individually.
You would need a wrench set to replace this pump.
• Make sure the unit is unplugged
• Disconnect tubes, belt, flywheel and pulley from the old pump
• Remove screws from the base which secure pump
• Remove old pump and secure new one using screws
• Reattach tubes, flywheel, pulley and belt
• Test the new pump
Join our VIP Email list
Receive money-saving advice and special discounts!
Thank you!
Error
Midvale, UT 84047
