
We Sell Only Genuine Campbell Hausfeld® Parts.
Campbell Hausfeld Air Compressor Parts & Models
Popular Campbell Hausfeld Air Compressor Parts

Genuine Campbell Hausfeld replacement part, this item is sold individually.
When you use a compressor the air that is compressed inside the tank will condensate and leave water inside the tank.
If it is left in the tank too long it can start to rust out the inside of the tank.
The Drain Valve should be opened up and let the water drain out.
The water will build up if you have a tendency to leave air in your tank for a long period of time.
You should drain your tank after each time it is used to prevent this from happening.

This is a genuine OEM sourced replacement part designed for use with air compressors. This breather acts as a valve for the fuel tank, it allows for the air to enter the fuel tank but it won't allow fuel or fuel emissions to leave the tank. It is made out of plastic and it is sold individually.
No special tools are needed to replace this Breather Assembly, simply screw it in the opening on the crankcase.

Genuine Campbell Hausfeld replacement part, this item is sold individually.
The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below.
Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air.
The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

Genuine Campbell Hausfeld replacement part, this item is sold individually.
The Ferrule in this case is used on all of the compressors listed below.
It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor.
It aids in stopping air leaks.

Authentic Campbell Hausfeld replacement part designed to work with Campbell Hausfeld Air Compressors. The pressure switch tells your compressor when to stop and when to start. There are multiple reasons a Pressure Switch could be leaking air. If it is leaking air the Pressure Switch should be replaced for a compressor to operate properly and safely.

This is a manufacturer sourced replacement pump assembly designed for use with Campbell Hausfeld air compressors. The purpose of the pump is to create pressure to in the air tank. This is a two (2) cylinder, cast iron pump. It is sold individually.
You would need a wrench set to replace this pump.
• Make sure the unit is unplugged
• Disconnect tubes, belt, flywheel and pulley from the old pump
• Remove screws from the base which secure pump
• Remove old pump and secure new one using screws
• Reattach tubes, flywheel, pulley and belt
• Test the new pump

Genuine Campbell Hausfeld replacement part, this item is sold individually.
When you use a compressor the air that is compressed inside the tank will condensate and leave water inside the tank.
If it is left in the tank too long it can start to rust out the inside of the tank.
The Drain Valve should be opened up and let the water drain out.
The water will build up if you have a tendency to leave air in your tank for a long period of time.
You should drain your tank after each time it is used to prevent this from happening.

This is a genuine OEM sourced replacement part designed for use with air compressors. This breather acts as a valve for the fuel tank, it allows for the air to enter the fuel tank but it won't allow fuel or fuel emissions to leave the tank. It is made out of plastic and it is sold individually.
No special tools are needed to replace this Breather Assembly, simply screw it in the opening on the crankcase.

Genuine Campbell Hausfeld replacement part, this item is sold individually.
The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below.
Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air.
The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

Genuine Campbell Hausfeld replacement part, this item is sold individually.
The Ferrule in this case is used on all of the compressors listed below.
It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor.
It aids in stopping air leaks.

Authentic Campbell Hausfeld replacement part designed to work with Campbell Hausfeld Air Compressors. The pressure switch tells your compressor when to stop and when to start. There are multiple reasons a Pressure Switch could be leaking air. If it is leaking air the Pressure Switch should be replaced for a compressor to operate properly and safely.

This is a manufacturer sourced replacement pump assembly designed for use with Campbell Hausfeld air compressors. The purpose of the pump is to create pressure to in the air tank. This is a two (2) cylinder, cast iron pump. It is sold individually.
You would need a wrench set to replace this pump.
• Make sure the unit is unplugged
• Disconnect tubes, belt, flywheel and pulley from the old pump
• Remove screws from the base which secure pump
• Remove old pump and secure new one using screws
• Reattach tubes, flywheel, pulley and belt
• Test the new pump