Repair Parts Home    Lawn Equipment Parts    Poulan Parts    Poulan Gas Chainsaw Parts    Poulan 2075C Type 5 Gas Chainsaw Parts
Poulan 2075C Type 5 Gas Chainsaw

 Poulan 2075C Type 5 Gas Chainsaw Parts

Page A
Page B
Page C
   Page A   

 Fig # Img Part Name Availability Price
A1Lever-Switch
Part #: 530038227
In stock
1 available
 $0.99
Add To Cart
A2Spring-Switch
Part #: 530016149
In stock
2 available
 $0.99
Add To Cart
A3Screw
Part #: 530015775
In stock
25+ available
 $2.99
Add To Cart
A4Kit-Line Tank/Purge
Part #: 530069216
In stock
25+ available
 $5.40
Add To Cart
A5Fuel Line Fitting
Part #: 530023877
In stock
25+ available
 $3.99
Add To Cart
A6Assy-Fuel Cap
Part #: 580940901
In stock
25+ available
 $4.12
Add To Cart
A7Kit-Trigger & Lockout
Part #: 530071305
Note: Includes Pin
In stock
14 available
 $3.99
Add To Cart
A8Wire-Throttle
Part #: 530037809
In stock
12 available
 $3.99
Add To Cart
A9Lever-Choke
Part #: 530047989
In stock
16 available
 $3.99
Add To Cart
A10Grommet-Choke Knob
Part #: 530038406
In stock
3 available
 $0.99
Add To Cart
A11Kit-Chassis Assembly Obsolete - Not Available
Part #: 530069822
Discontinued
N/A
A11
Assembly-Chassis 2075C
Part #: 530056605
Ships in 4 - 8 business days
 $50.05
Add To Cart
A11
Assy-Chassis
Part #: 530056606
Ships in 4 - 8 business days
 $44.59
Add To Cart
A12
Nut-Speed
Part #: 530015922
Backorder:
Unavailable until 05/05/2015
 $0.99
Add To Cart
A13Assembly-Chain Brake (Green)
Part #: 545139906
In stock
25+ available
 $28.12
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A13Assembly-Chainbrake (Camo)
Part #: 530055190
In stock
2 available
 $28.15
Add To Cart
A13Assy-Chain Brake
Part #: 545139902
In stock
7 available
 $21.96
Add To Cart
A14Assembly - Clutch
Part #: 530014949
In stock
25+ available
 $7.66
Add To Cart
A15Washer-Clutch
Part #: 530015611
In stock
25+ available
 $3.99
Add To Cart
A16Clutch Drum and Gear Assembly
Part #: 530047061
In stock
25+ available
 $16.01
Add To Cart
A17Washer - Thrust
Part #: 530015907
In stock
25+ available
 $3.99
Add To Cart
A18Flywheel Ass'y.
Part #: 530047534
In stock
16 available
 $21.73
Add To Cart
A19Flywheel Washer
Part #: 530015127
In stock
17 available
 $3.99
Add To Cart
A20Nut-Flywheel
Part #: 530016134
In stock
13 available
 $3.99
Add To Cart
A21Screw
Part #: 530015920
In stock
15 available
 $3.99
Add To Cart
A22Handle-Starter
Part #: 530056402
In stock
25+ available
 $3.99
Add To Cart
A23Rope (3 ft.)
Part #: 530069232
In stock
25+ available
 $3.99
Add To Cart
A24Housing-Fan
Part #: 530049334
In stock
11 available
 $8.38
Add To Cart
A24
Housing-Fan 2075C
Part #: 530055188
Ships in 4 - 8 business days
 $16.16
Add To Cart
A24
Housing-Fan 2075OC
Part #: 530056049
Ships in 4 - 8 business days
 $15.70
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A25Screw.
Part #: 530015892
In stock
25+ available
 $1.99
Add To Cart
A26Spring-Starter
Part #: 545008015
In stock
25+ available
 $3.99
Add To Cart
A27Starter Pulley Obsolete - Limited Quantity
Part #: 545034301
In stock
1 available
 $7.44
Add To Cart
A28Rope Retain Screw
Part #: 530016080
In stock
25+ available
 $3.99
Add To Cart
A29Starter Dog Spring
Part #: 530023817
In stock
18 available
 $2.99
Add To Cart
A30Kit-Oil Vent
Part #: 530071666
In stock
3 available
 $7.28
Add To Cart
A31Handle-Front Obsolete - Not Available
Part #: 530059173
Discontinued
N/A
A32Screw
Part #: 530015814
In stock
25+ available
 $1.99
Add To Cart
A33Assembly-Oil Cap w/ret.
Part #: 530057236
In stock
25+ available
 $5.22
Add To Cart
A34Screw
Part #: 530016132
In stock
25+ available
 $2.99
Add To Cart
A35Chain Catcher
Part #: 530029850
In stock
25+ available
 $3.99
Add To Cart
A36Screw
Part #: 530015814
In stock
25+ available
 $1.99
Add To Cart
A37Plate-Bar Mounting
Part #: 530038238
In stock
25+ available
 $3.99
Add To Cart
A38Nut - Bar Mounting
Part #: 530015917
In stock
25+ available
 $2.99
Add To Cart
A39Pin - Bar Adjust
Part #: 530015826
In stock
25+ available
 $2.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A40Kit - Bar Adjust
Part #: 530069611
Note: Includes figures 39 and 41
In stock
25+ available
 $4.04
Add To Cart
A41Retainer - Bar Adjust
Part #: 530038593
In stock
25+ available
 $2.99
Add To Cart
A42Bar 14"
Part #: 952044368
In stock
25+ available
 $26.27
Add To Cart
A42Bar 16"
Part #: 952044370
In stock
25+ available
 $28.55
Add To Cart
A42Bar 16"
Part #: 952044370
In stock
25+ available
 $28.55
Add To Cart
A42Bar-18
Part #: 952044418
In stock
19 available
 $30.24
Add To Cart
A43Chain 14"
Part #: 581562101
In stock
25+ available
 $18.26
Add To Cart
A43Accy-16" Chain
Part #: 581562201
In stock
25+ available
 $20.46
Add To Cart
A43Chain-18
Part #: 581562301
In stock
25+ available
 $27.30
Add To Cart
A44Kit-Oil Pump
Part #: 530071259
Note: Includes figures 45, 46 and 48
In stock
25+ available
 $14.16
Add To Cart
A45Gear-Worm Spring
Part #: 530037820
In stock
25+ available
 $3.99
Add To Cart
A46Elbow-Oil Pickup
Part #: 530049477
In stock
1 available
 $0.99
Add To Cart
A47Scp#6-19 x .437 .Pl. Pan.
Part #: 530016064
In stock
25+ available
 $2.99
Add To Cart
A48Seal Block
Part #: 530019206
In stock
8 available
 $3.99
Add To Cart
A49Oil Pickup Assembly
Part #: 530047663
Note: Includes figures 50-52
In stock
25+ available
 $3.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A50Pickup-Oiler
Part #: 530038373
In stock
1 available
 $1.61
Add To Cart
A51Oil Intake Screen
Part #: 530056533
In stock
2 available
 $3.99
Add To Cart
A52Oil Intake Screen
Part #: 530056533
In stock
2 available
 $3.99
Add To Cart
A53Screw
Part #: 530015940
In stock
24 available
 $2.99
Add To Cart
A54Bolt-Handguard Obsolete - Not Available
Part #: 530016020
Discontinued
N/A

Enter your engine's type number in this search field to show the parts that match your engine.

Your engine's type number is the second part of the model number stamped on your Briggs & Stratton engine (see picture).

Saw Parts  Chain Saw Parts

Repair Articles

How to Test a Small Engine for Spark
How to Test a Small Engine for Spark

If your small engine isn't starting, you'll need to diagnose many issues including the spark plug. This video walks you through the steps of how to test for a spark using a spark tester.
How to Replace the Oiler Assembly on a Chainsaw
How to Replace the Oiler Assembly on a Chainsaw

Follow this easy guide to make a stressful problem into an easy repair. In less than an hour you can repair the oiler assembly on your chainsaw by following this guide.
Quick Fix: How to Clean a Spark Arrestor Screen on a Small 2-Cycle Engine
Quick Fix: How to Clean a Spark Arrestor Screen on a Small 2-Cycle Engine

This repair article will instruct you how to repair a dirty or damaged spark arrestor on your small engine.
Quick Fix: How to Replace the Spark Plug in a Small Engine
Quick Fix: How to Replace the Spark Plug in a Small Engine

This article will help you replace the spark plug on a small engine which will help get your gas powered equipment up and running again.
Discussion
Discussion for the Poulan 2075C Type 5 Gas Chainsaw

Post a Comment
Login or signup to comment.
Login or signup to comment.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
broyal
Question: Fuel Line Insertion

broyal

What is the trick to insert the fuel line through the hole to the fuel tank which it will also seal? I tried without any luck.
1149905
Reply: Fuel Line Insertion

1149905

Im wondering the same thing that you are. Do you happen to know where to find the answer?
1151683
Reply: Fuel Line Insertion

1151683

I have the same problem, can not insert the fuel line tube.
I need to replace the piece with the teeth on it. How hard is it to remove?
zmmmarkie
Reply: How To Remove The Assembly Drum?

zmmmarkie

You need to remove the cover directly across from the centrifical clutch. It has a bunch of fins that you will see. You will need a strong gripped person to grip the fins. please remember to tell that person not to break them! Then you take a wide flat blade screwdriver and a hammer on top of the clutch it says off and on rest the screwdriver on the edge of the off side one sharp tap should do it. When it moves very little you then can unscrew in the off direction the entire clutch will come off. Pay close attention at the springs and counter weights because you will have to remove them. A picture might help. Good luck Gonzo,
Mark
1stumpman
Reply: How To Remove The Assembly Drum?

1stumpman

Remove sparkplug put 2inchs of rope in plug hole uses channel lock to turn counterclockwise
1stumpman
Reply: How To Remove The Assembly Drum?

1stumpman

Sorry clockwise
ShotOut
Reply: How To Remove The Assembly Drum?

ShotOut

The part with TEETH on it. Clutch DRUM and Clutch assembly have no teeth. For those that care, the clutch drum is held on to the end of the engine's crankshaft with a TORX 20 screw. You loosen the screw to REMOVE the drum. The screw does NOT come out, but stays inside the drive-neck of the clutch drum. Good advice on using the rope though. It works. Flywheel removal is fun. Maybe that is the part the OP said had "teeth." By the way, the original post on this problem is 2.75 years old. Did you get it off yet??
ShotOut
Reply: How To Remove The Assembly Drum?

ShotOut

The part with a "bunch of fins" is called the FLYWHEEL.
dejajay75
Question: Module- Ignition Coil

dejajay75

will this part fit mychainsaw 2025 mine will crank not firing
WJA
Reply: Module- Ignition Coil

WJA

Hello dejajay75,

The 530039198 is the ignition coil for the Poulan 2025 chainsaw. It also is used on quite a few of their other gas engines.

Hope this helps,
WJA
Replacing fuel lines and primer bulb, not sure which lines go where, such as the two lines one small one larger from primer bulb. I am pretty sure larger line goes in fuel tank but I am not sure if the small line should go to the top feed of carberatur or lower feed. Also does it make a difference how the lines are installed onto the primer bulb itself. Would appreciate some help on this matter Thanks.
UtahAV
Reply: Replacing Fuel Lines And Primer ...

UtahAV

The fuel system on your chainsaw has a filtered inlet that goes to the input tube of the carburetor. The other hose on the carb is the priming hose. It runs from the carb outlet to the input, or suction side, of the primer bulb. The last line runs from the output side of the primer bulb back to the fuel tank. It is the return line.

When you prime your saw the primer pulls filtered fuel into the carb, to the primer bulb and then returns excess back to the tank. To find the suction side of the primer bulb, attach a piece of fuel line to one side of the primer. Now put the line in a small container of fuel. If you see bubbles when you press the bulb, the hose is hooked to the outlet side of the primer. If it sucks fuel into the bulb then you have found the suction side.
Identifying the input and output side of a carb that has a remote priming assembly can be very difficult and there is no rule that applies in every case. Usually you just need to use trial and error on those connections. If you have hooked everything up so you are pulling fuel through the carb, not pushing it into the carb, and your saw won't fire, you should just need to swap the lines on the carb and then it should run fine. The important thing is that you have the priming lines setup to pull fuel through the carb.

I hope this helps!

-UtahAV
-Mark
arnie
Question: No-gas

arnie

HI GUYS, I HAVE REBUILT SEVERAL CARBS AND HAD GOOD LUCK. NOW, I HAVE JUST REBUILT TWO MORE AND THEY WILL ONLY RUN WHEN I POUR GAS IN THEM. I HAD THEM APART TWO-THREE TIMES, SAME THING. TELL ME WHAT I AM MISSING. THANKS, ARNIE
Forrest Matheney
Question: Poulan Fuel Lines Diagram

Forrest Matheney

I have a Poulan 2075 chain saw. My fuel lines are crumbled and I cannot determine the proper connections. Should there be a filter attached to the line in the fuel tank? Where can I get a complete fuel line diagram?
Larry Bridges
Reply: Poulan Fuel Lines Diagram

Larry Bridges

I couldn't find a diagram. Begin with the large line from the Primer Bulb. It goes to the upper right entrance into the tank. Inside the tank it connects to a little bulb stop. It may still be connected to the line entrance. With needle nose pliers, reach inside the tank and pull this bulb out. Replacing a new line to the large Primer line feed is difficult.

Next is the small tube from the Primer Bulb to the Carburetor. That's pretty simple. Finally, a long small fuel line with a fuel filter inside the tank goes to the plastic connection above the Carburetor. This one is tough to install. You need about 2 feet of line to be safe. Trim 2" off one end. This tube inserts from the left of the Carburetor into the tank. Insert the trimmed end. With needle nose pliers, reach inside the tank and pull the tube in. You may want to lubricate the line with oil or soap. Pull 7" of line through, then replace the filter and put in back into the tank into an elongated area towards the front of the tank. You need enough line inside the tank so it can move freely inside the tank. Trim off the excess line and connect to the black plastic inlet. If you need a Primer Bulb, don't worry about the tube inlets differing from the old Primer. Just plug the new tubing onto them. They'll work just fine.
teddy
Question: Poulan 2075 Oiler

teddy

How do I install an oiler kit in my saw?
Terry
Question: Sprocket Removal

Terry

How do I get the clutch assembly
# 16 on the parts list off the saw and apart to replace the sprocket?
I want to replace the fuel lines in my Poulan 2075 chain saw when I replace the primer bulb. How is this done?
amazontoolrepair
Reply: How Do You Replace Fuel Lines In...

amazontoolrepair

It's fairly simple if you are somewhat mechanically inclined however there are some small parts so pay attention to what you are removing. Start by getting the right size fuel line, fuel filter and primer bulb. Drain the fuel out of the gas tank, pump the primer bulb a few times then drain the remainder out of the tank. Take the top cover off to expose the air filter (3, T20 or T25 torx screws). Remove the air filter by simply un-clipping it, this will reveal some more torx screws to remove the carburetor. Lift the carburetor up, open the fuel cap (to release pressure) and then simply pull on the fuel lines to remove them from the carburetor (you may need to get a flat tip screw driver for leverage to get them off). In the gas tank you will need to get a wire hook to grab the fuel line, pull it out of the filler hole and remove the fuel filter. Now back by the carburetor you can pull the fuel line through the top. Replace it with your new fuel line and thread it through the hole, pull it out the filler hole and put the new fuel filter on. The primer bulb and its lines are to the left of where the carburetor is so do the same with the lines running to that, the primer bulb just unclips to remove from casing. I like to do one line at a time so you don't mix up there sizes or make any mistakes. Once you have all 3 lines and the primer bulb you can go ahead and put it back together.
That should be all.
Good luck!
680857
Question: How To Replace Fuel Lines?

680857

How do you replace new fuel lines when relacing the primer bulb?
fancyboxy