Medium
1-2 hours
It is an authentic manufacturer sourced replacement part that is specially designed for Hitachi power equipment. This o-ring provides an air-tight seal for the valve piston, for correct location and use of this item make sure to check appropriate diagrams of your model. Over time o-rings may deteriorate and crack eventually requiring replacement. It is made from high-quality rubber material and it is sold individually.
O-ring (1ap-10) 872654
OEM part for: Metabo HPT (Hitachi)
Part Number: 872654
$5.19
In Stock
Order within the next 2 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 38 machines
Metabo HPT (Hitachi)
NR90AE 3-1/2" Round Head Framing Nailer View Diagrams & Manuals
NT50AE2 2" 18-Gauge Brad Nailer View Diagrams & Manuals
CR13VA Electric Variable Speed Reciprocating Saw View Diagrams & Manuals
CR13VBY 12 Amp Low Vibration UVP Reciprocating Saw View Diagrams & Manuals
DH18DL 18V 3.0Ah Lithium Ion SDS Plus Rotary Hammer View Diagrams & Manuals
DH22PG 7/8" SDS Plus Rotary Hammer View Diagrams & Manuals
M12SA2 3-1/4 Peak HP Single Speed Plunge Router View Diagrams & Manuals
N3804AB3 1/4" Narrow Crown Stapler View Diagrams & Manuals
CR10V Reciprocating Saw 6.5Amp View Diagrams & Manuals
CR13VB Reciprocating Saw View Diagrams & Manuals
DH25V 1" Rotary Hammer View Diagrams & Manuals
M12V2 Router View Diagrams & Manuals
N3804AB3(S) Stapler View Diagrams & Manuals
NR90AD Strip Nailer View Diagrams & Manuals
NR90ADPR Strip Nailer View Diagrams & Manuals
NR90AE(S) Strip Nailer View Diagrams & Manuals
NR90AF Strip Nailer View Diagrams & Manuals
NT32AE2 Brad Nailer View Diagrams & Manuals
NT50AE2(S) Brad Nailer View Diagrams & Manuals
NT65MA4(S) Finish Nailer View Diagrams & Manuals
NT65MA4 Finish Nailer View Diagrams & Manuals
DH18DSLP4 Cordless Rotary Hammer View Diagrams & Manuals
NV90AG Coil Nailer View Diagrams & Manuals
NP14DSL Nailer View Diagrams & Manuals
NP18DSL Nailer View Diagrams & Manuals
NR90AC5M 3-1/2 Inch Rnd Head Framing Nailer View Diagrams & Manuals
M12V2M 3-1/4 +a5082:b5096hp Plunge Router, Variable Speed (Evs), 1/2 Inch Collet View Diagrams & Manuals
M12VEM 3-1/4 Hp Plunge Router, Variable Speed (Evs), 1/2 Inch Collet View Diagrams & Manuals
CR10VB View Diagrams & Manuals
DH18DLP4 Rotary Hammer View Diagrams & Manuals
DH25Y Demolition Hammer View Diagrams & Manuals
DH28Y Hammer Drill View Diagrams & Manuals
NR90AC5 Nailer View Diagrams & Manuals
NR90AEPR Nailer View Diagrams & Manuals
NR90AE(S1) Nailer View Diagrams & Manuals
NT65M2S Nailer View Diagrams & Manuals
NV65AH2 Nailer View Diagrams & Manuals
NV90AG(S) Nailer View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Nailer Parts
- Reciprocating Saw Parts
- Saw Parts
- Rotary Hammer Parts
- Router Parts
- Stapler Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for O-ring (1ap-10)
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
air leak causing frequent compressor cycling
Lennie - June 2, 2023
Tool Type
Nailer
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Pliers, Nutdriver, snap ring plier, allen wrenches 3,4,5mm, punch set
disassemble tool, clean parts, reassemble with new o-rings, bumper, exhaust valve, gasket.
Beware that the O-rings sold from a Chinese supplier (seller on the Big A place) are not the same size as the OE parts. Some work OK but it would be better if HPT offered a complete kit instead of just individual seals. The small kit offered by HPT was insufficient to my needs. My nail gun is a NV65AH2 and there is very little about it on YT as well. Removing the roll pin for the feeder piston was tricky. We had to use a straight grip plier to get it to move and then we could tap it out without ruining the piston shank. If not careful, you will break the nose 888007. Also be advised that screw #73 must have the head on the left side of the nose or the feeder cannot advance the nails.
Beware that the O-rings sold from a Chinese supplier (seller on the Big A place) are not the same size as the OE parts. Some work OK but it would be better if HPT offered a complete kit instead of just individual seals. The small kit offered by HPT was insufficient to my needs. My nail gun is a NV65AH2 and there is very little about it on YT as well. Removing the roll pin for the feeder piston was tricky. We had to use a straight grip plier to get it to move and then we could tap it out without ruining the piston shank. If not careful, you will break the nose 888007. Also be advised that screw #73 must have the head on the left side of the nose or the feeder cannot advance the nails.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
