Miter Gauge Assembly 089037007707
Part Number: 089037007707
Order within the next 5 hours
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: 089015001009 and 089015001009 (02-15-19 (Rev:03)).
Product Information
Description:
This replacement miter gauge assembly is specially manufactured for a Ryobi table saw. It is an authentic OEM sourced item, not an aftermarket imitation. The purpose of a miter gauge is to allow user to position and safely guide the workpiece. It is inserted into either one of the two t-slotted grooves located in the table top. This gauge consists of a plastic bracket, a knob and a metal rail. This miter gauge can be turned 60° to the right or left. • Loosen the lock knob • Rotate the gauge until the desired angle • Tighten the lock knob |
Frequently Purchased With
Products Compatibility
This item works with the following types of products:
- • Saw
- • Table Saw
Questions & Answers for Miter Gauge Assembly
What are the dimensions of the bar?
Brad
for model number 113.221611
asked on 2022-11-28
Hello Brad, Thank you for the question. This Bar is approximately 5/8" X 10.5". Thank you for your inquiry, good luck with this repair!
eReplacementParts Team November 28, 2022
Will miter guide #089037007707 fit the Craftsman model 137.248480 table saw?
Anthony
for model number 089037007707
asked on 2023-04-21
Hello Anthony, thank you for writing. No, this Gauge will not fit. Good luck with your repair.
eReplacementParts Team April 21, 2023
Does this miter guage fit RTS12
Curt
for model number RTS12
asked on 2023-11-09
Hello Curt, Thank you for writing. The Miter Gauge for this model is Part Number 089240035706. Thank you for reaching out!
eReplacementParts Team November 09, 2023
What is the size of the mitre that fits in the groove of the table saw? I have a 9" craftsman.
Ross
asked on 2023-10-31
Hi Ross,
Thank you for your question. The miter measures approximately 5-1/4 inches by 3-3/8 inches. We hope this helps!
eReplacementParts Team October 31, 2023
will it workGW15056D1C33962
chuck
for model number ridgid R4513
asked on 2023-10-19
Hi Chuck,
Thank you for your question. This would not be the correct miter gauge assembly for your table saw. The part number for the miter gauge assembly is 089290001708. We hope this helps!
eReplacementParts Team October 19, 2023
Is this fit their Craftsman 137 model
Bryan
asked on 2023-03-25
Hello Bryan, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the full model number of the unit, as 137 appears to be only a partial model number. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you.
eReplacementParts Team March 25, 2023
Will this fit a full size Craftsman table saw model 285A?
Elaine
for model number E234117 or 285A
asked on 2023-02-24
Hi Elaine,
Thank you for your question. Before we can provide you with information on miter gauge assembly, we will need the complete model number from the table saw. It is usually found above the Craftsman logo on the front right side of the table saw. If you could resubmit your question with this information, we would be happy to help you. If the information you provided is correct, you will need to contact Craftsman for information. If you have any questions, please let us know.
eReplacementParts Team February 24, 2023
Is this for a full size Craftsman table saw?
Elaine
asked on 2023-02-17
Hi Elaine,
Thank you for your question. Yes, this miter gauge assembly can be used on a Craftsman table saw. If you could resubmit your question with the model number from your table saw, we will verify if it is the correct part for it. It will usually be found above the Craftsman logo on the front right side of the table saw. We look forward to hearing from you!
eReplacementParts Team February 17, 2023
Has anyone used this miter gauge assembly (089037007707) for the RTS12 table saw?
Andrew
for model number RTS12
asked on 2022-11-24
Hello Andrew, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part Number: 089240035706. Thank you for your inquiry, good luck with this repair!
eReplacementParts Team November 24, 2022
need the 5/8 bar on the miter slide, can i get it
Irvin Jones
for model number RTS10 table saw
asked on 2022-03-28
Hello Irvin, thank you for writing. We do have the Miter Gauge Assembly 089037007707 but do not see a 5/8 bar in the parts list. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
eReplacementParts Team March 28, 2022
Repair Instructions: Submitted by Customers Like You
7 of 7 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, None required
My Ryobi table saw was missing the Miter gauge
No tools where needed, just slipped it into place.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Power Drill, Nutdriver, Adjustable Wrench
Had no miter guage
Had to remove Wrong miter guage from Ryobi table saw how someone paired a wrong guage with this saw I will never forget ! Ordered Correct guage + assembled it + added a six inch by 1.5 height hickory wood to the face of miter guage ,to give it Perfect alignment Job task completed ! Just ask Stevie S the FIXER ! Greetings from Williamsville NY to you repair nuts !!!!!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Socket set, Wrench Set, Adjustable Wrench
I bought it on OfferUp and it was missing some stuff
With patience and focus and the right tools
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
, Grinder
Lost part / Your replacement did not fit . Needed to be modified
I had to reshape the guide to fit the table saw. Original replacement was too wide to fit track
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, Small file to clean brush holder.
Motor runs poorly if at all, Elv. Shaft damaged. Trash picked, therefore previous owned caused issues.
Brush
1. Removed the motor from the saw and disassembled the brush area of the motor.
2. Determined the sticking brush and removed it from the motor.
3. Determined why the brush was sticking (not or poorly contacting the armature). The brush guide was slightly damaged and needed to be cleaned (small file to remove rough edge). Likey dirty and overheated to start to distort the plastic brush guide.
4. Inspected armature for excessive wear, it was generally clean and didn't need work.
5. Reasembled brush and brush guide, checked for free movement and reassembled motor.
6. Reinstall motor and tested, working just fine now.
Elv. Shaft
1. Much easier, just removed retaining clip at end of shaft and unscrewed shaft from saw.
2. Installed new Elv. Shaft by screwing back into place.
3. Installed a new retaining clip. Replacing all washers in their correct order.
4. 3D printed a new handle and installed on to the Elv. shaft.
5. Works just fine now.
Miter Gauge Assembly
1. Just slid it into the track on the saw bed.
1. Removed the motor from the saw and disassembled the brush area of the motor.
2. Determined the sticking brush and removed it from the motor.
3. Determined why the brush was sticking (not or poorly contacting the armature). The brush guide was slightly damaged and needed to be cleaned (small file to remove rough edge). Likey dirty and overheated to start to distort the plastic brush guide.
4. Inspected armature for excessive wear, it was generally clean and didn't need work.
5. Reasembled brush and brush guide, checked for free movement and reassembled motor.
6. Reinstall motor and tested, working just fine now.
Elv. Shaft
1. Much easier, just removed retaining clip at end of shaft and unscrewed shaft from saw.
2. Installed new Elv. Shaft by screwing back into place.
3. Installed a new retaining clip. Replacing all washers in their correct order.
4. 3D printed a new handle and installed on to the Elv. shaft.
5. Works just fine now.
Miter Gauge Assembly
1. Just slid it into the track on the saw bed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, none
Replacement for original miter gauge assembly.
I some how misplaced or lost the original Miter Gauge Assembly for my Ryobi table saw.
Once the part arrived, it fit perfectly and I can now use my table saw as intended.
It required no tools.
Once the part arrived, it fit perfectly and I can now use my table saw as intended.
It required no tools.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Hard
Time Spent Repairing:
30-60 minutes
Tools Used:
, Grinder
Part said it was for the Ryobi table saw but I had to grind off the flanges and add washers to make it fit my model. I spent about 40 minutes making these adjustments before I made it fit.
Ground off the flanges and some of the height.
Added washers to all screws
Ground off some of the flanges on the table saw to allow mitre gauge to fit.
Added washers to all screws
Ground off some of the flanges on the table saw to allow mitre gauge to fit.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, my hands
missing mitre assembly
bought it. set it in groove- done in 10 seconds
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
No miter gauge
Miter gauge fits sloppy in slots and cannot get a straight cut.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
The Miter Gauge Assembly was lost in a move
Placed it on the saw
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
14 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
9
4 stars
2
3 stars
0
2 stars
0
1 stars
3
< PREV
- 1
- 2
Fast and honest people.
Fast and efficient service
Guest -
May 27, 2023
Verified Purchase
Worked as expected
Worked as expected in portable table saw
Guest -
May 24, 2022
Verified Purchase
As Adversitised
Good price, good delivery, good product - especially for the price.
Guest -
November 3, 2021
Verified Purchase
Great purchase choice with low price.
Exactly as advertised. With minor modifications, fits my saw perfectly. The complete description is what convinced me to buy from you.
Guest -
September 14, 2021
Verified Purchase
Just what I wanted. Worked great.
Happy with everything, except I would have liked some basic measurements. I have an older saw and wasn't sure if this part was right?
Guest -
May 28, 2020
Verified Purchase
Quick and easy
Perfect match for my saw. Arrived quickly. Spent a day with the actual company of the part I needed and couldn’t get anywhere. So glad I found ereplacementparts.
Guest -
April 22, 2020
Verified Purchase
Awesome part
Dyxuxi
Guest -
November 28, 2019
Verified Purchase
Miter gsuge
Very satisfied with my order. Part was a perfect fit. Easy to order and delivery was fast and flawless. Very satisfied with the experience.
Guest -
August 20, 2019
Verified Purchase
Great part
Great part but to no fault of ereplacementparts it did not fit because my table saw has no grooves in the table, very well made part otherwise, other consumers check your table saw first to make sure it has slots in the table top to accommodate this miter gauge assembly.
Guest -
August 16, 2019
Verified Purchase
Was as expected,fit right on my saw
Made it easier to cut fewer angles then having to get out my mitersaw
Guest -
March 27, 2023
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
- 2
Product Information