Easy
15-30 minutes
This high quality fuel tank assembly is utilized on a Homelite blower. It is a genuine OEM sourced item, not an aftermarket equivalent. The purpose of this tank is to hold the fuel needed for the engine to run. This assembly includes a plastic fuel tank, the fuel lines and the cap. Over time it may deteriorate allowing for leaks and requiring replacement. Please note the hardware to secure this tank is sold separately. You will need a screwdriver to complete this repair.
Fuel Tank With Cap Assembly 308675007
OEM part for: Homelite
Part Number: 308675007
$6.57
In Stock
Order within the next 3 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This item works with the following types of products:
- Blower Parts
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
7
4 stars
1
3 stars
0
2 stars
1
1 stars
0
< PREV
- 1
Great Replacement
The replacement fuel tank was a perfect fit. It only took a few minutes to install the new tank. It works as it should.
Guest -
October 3, 2023
Verified Purchase
Great service- Super fast delivery
I was surprised at the size difference between the original tank and the replacement tank, which was considerably smaller, but it all fit right in and my repair was completed in minutes.
Guest -
June 20, 2022
Verified Purchase
Great service
The fuel tank was correct and the price was great, just as important to me was the Great Service, from price to delivery date. My hedge trimmer runs like new again.
Guest -
May 6, 2022
Verified Purchase
Redesigned fuel tank - vibration resistant
Although the replacement fuel tank is smaller it fit perfectly and was muck more resistant to vibration cracking. A good redesign.
Guest -
December 11, 2021
Verified Purchase
New fuel tank was great.
The tank fit like a glove! It even came with the fuel lines and strainer installed. The old Homelite Leaf blower still runs like a new one. Thanks,
Guest -
November 17, 2020
Verified Purchase
Homelite Blower Tank
It came complete with hoses, filter, & cap and worked like a champ!
Guest -
July 19, 2019
Verified Purchase
Easy to swap out . Just as described.
It came fast. Looks great.
Ron -
May 21, 2019
Verified Purchase
Works- fits
Arrived quickly. The tank fits and works well, but the tank is smaller then the original.
Guest -
June 3, 2019
Verified Purchase
Replacement for Recall on Homelite Blower leaky tank
Specifically shown as the exact replacement tank and part # for my blower. When received, the tank was 1/4 smaller all around than the one on the website. Returning for a refund. They don't have the one advertised on their site
Guest -
June 14, 2019
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Fuel Tank With Cap Assembly
I need fuel tank for this vac attack 11 200 mph 30cc family 5hcps 0304ab
Anthony
for model number UT-08542-A
asked on 2023-03-01
Hello Anthony, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part Number: 308123004. Good luck with the repair!
eReplacementParts Team March 01, 2023
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
replace leaking tank, remove tank and install new tank
Wolfgang - December 6, 2015
👍 17 of 18 people found this instruction helpful
Tool Type
Blower
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Easy installation,
1. Remove three bolts, fuel lines and old tank, make note of where the fuels lines go.
2. Install new tank with the existing 3 mounting bolts
3. Connect the new fuel lines which are part of the supplied tank
4. Recycling of the old tank
I recommend ereplacementparts!
1. Remove three bolts, fuel lines and old tank, make note of where the fuels lines go.
2. Install new tank with the existing 3 mounting bolts
3. Connect the new fuel lines which are part of the supplied tank
4. Recycling of the old tank
I recommend ereplacementparts!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Hole in primer hose.
Raymond - June 3, 2017
👍 3 of 3 people found this instruction helpful
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Nutdriver
Parts Used
Replacement was easy. I had to do this on another blower so I knew exactly what to do. I first removed the lines from the carb unbolted the tank and replaced it with the new one. Everything works good and the repair job is done.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Gas tank was leaking. It had a Crack by the center mounting hole.
John - April 5, 2018
👍 1 of 1 people found this instruction helpful
Tool Type
Blower
Difficulty
Medium
Time
Less than 15 minutes
Tools Used
Nutdriver
Parts Used
Removed3 bolts, the old tank, and fuel lines.
Installed new tank, and reconnected fuel lines.
Installed new tank, and reconnected fuel lines.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tank was leaking at fuel line
Bobby - October 19, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Blower
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
Take the fuel lines off of the carburetor
Remove the screws holding the fuel tank on
Install the fuel tank with the screws
Connect the fuel lines
Remove the screws holding the fuel tank on
Install the fuel tank with the screws
Connect the fuel lines
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Gas lines split, old aged plastic.
Raymond - May 14, 2023
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Nutdriver
Parts Used
Removed fuel lines, unscrewed gas tank (3 screws). Cut new fuel lines to length. Connected new fuel lines. Screwed gas tank on. Done.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
needed gas tank
Raymond - December 18, 2019
Tool Type
Blower
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Nutdriver
Parts Used
Replaced gas tank with new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Fuel tank had a hole in it
Dana - October 12, 2017
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Removed fuel lines off the carb
Unscrewed the tank mounting screws and removed the tank.
Install the tank in the reverse order as removal just make sure you pay attention to the fuel lines they are easy to swap.
Unscrewed the tank mounting screws and removed the tank.
Install the tank in the reverse order as removal just make sure you pay attention to the fuel lines they are easy to swap.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
My gas tank (plastic) wore a hole thru the center where a screw goes. With all the vibration, the screw cut the plastic tank.
Chuck - October 4, 2017
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
I removed the old tank (3 screws) and hoses to carb. Then I put it back together
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Blower tank replacement
Raymond - May 16, 2017
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
I replaced the tank before, so the installation went easy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Fuel tank cracked at center mounting screw
Jeff - December 5, 2016
Tool Type
Blower
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Needle nose pliers
Parts Used
1. Drained out remaining fuel.
2. Disconnected fuel lines
3. Removed 3 mounting screws
4. Removed old tank
5. Reinstalled new tank with previous screws removed
6. Connected new fuel lines that cane with tank
7. Added fuel, checked for leaks
8. Went thru starting procedures
9. Unit started and ran fine
2. Disconnected fuel lines
3. Removed 3 mounting screws
4. Removed old tank
5. Reinstalled new tank with previous screws removed
6. Connected new fuel lines that cane with tank
7. Added fuel, checked for leaks
8. Went thru starting procedures
9. Unit started and ran fine
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
