Repair Parts Home Power Tool Parts DeWALT Parts DeWALT Grinder Parts
DeWALT D28402 Type 1 Small Angle Grinder Parts
Quick Fix: How to Replace the Gear Box on a DeWalt D28402 Grinder
When the gear box on your grinder breaks, you don't have to replace the entire tool. You can order the gear box and replace it yourself in about 10 minutes.
Quick Fix: How to Replace the Switch on a DeWalt D28402 Grinder
Learn the steps needed to replace the switch on a grinder, which will help get your tool running in tip-top shape again.
Quick Fix: How to Replace the Brushes on a DeWalt D28402 Grinder
This article outlines the steps needed to replace the brushes in a DeWalt grinder.
How to Diagnose a Bad Power Cord or Switch
This article outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test tool and appliance cords and switches, the two parts usually responsible for electri...
Time Spent Repairing:
Entry Date:2013-10-22 10:52:35
2 of 2 customers found these instructions helpful
Brushes wore out no power
Unplug it ,take lower handle screws out,remove screw side half of handle cover,take a picture of wire placement,remove other side cover, remove brush lead with needle nose pliers, replace brushes,put back together. done.
Time Spent Repairing:
Less than 15 minutes
Entry Date:2013-10-07 16:30:42
0 of 0 customers found these instructions helpful
BRUSHES WORE OUT
First remove the screws from rear housing,take housing apart. While a part checked other parts for wear. Then removed old worn brushes and replaced with new ones. Runs like a new tool. Easy repair TAKE OUT OLD BRUSHES THEN PUT IN NEW ONES
Discussion for the DeWALT D28402 Type 1 Small Angle Grinder
Post a Comment
Ask a question, answer a question, or post a comment!
Question: Amateur & Field
I recently replaced the armateur and field on my D28402 grinder and upon reassembly I'm getting a loud winding or rubbing link removed figure out where it's coming from.Any help?
Reply: Amateur & Field
That could be a couple of things.First make sure that the rubber boot is on the end of the armature bearing.This boot is a dampener and if you leave it off it will allow the armature to spin slightly off the center of its axis causing the armature to rub on the field.Check that the armature fan is not rubbing on the baffle.If I remember right some of the baffles can be installed 180 degree's the wrong way as this would allow the fan to rub on the baffle.And lastly check all your switch wiring and make sure it tuck into the clam shell canals as not to rub on the armature.Hope this helps.Good luck.
Question: D28402 Spindle Button
On a dewalt d28402 grinder can the spindle lock button on the gearcase be replaced? If so how? could not find seperate replacement part #.
Reply: D28402 Spindle Button
The spindle lock assembly is part of the 623586-00SV Gear Case Assembly. The manufacture does not sell individual parts for the spindle lock. Make sure of you model number and type, there are a couple of different gearcase assemblies depending on the correct model and type.
Question: Dewalt Angle Grinder Dead
I have 2 dewalt angle grinders that won't start (models D28110 and D28402). One of them is totally dead, the other will occasionally start for a split second, then die.
Any suggestions on what to look for when I open them up, besides checking the switch for continuity? Can you tell through visual inspection if the brushes are bad?
First always check your cord to make sure you are getting power to your switch. If you are then check out your switch with your tester and make sure it is functioning. Always check for any wire that might have come loose, and also your brushes, if you have one that is completely gone you might just need a set of brushes, hope this will help someone!
Review: DeWALT - D28402 D28402
I have used and have worked on many brands of small grinders and in my opinion this one is as good as any I have used and better than most. They rarely need much other than a set of brushes once in a while. With proper care will last a long time and do a lot of work!
Accessories for the D28402