Repair Parts Home    Power Tool Parts    DeWALT Parts    DeWALT Grinder Parts    DeWALT D28110 Type 1 Grinder Parts
DeWALT D28110 Type 1 Grinder dewalt logo

 DeWALT D28110 Type 1 Grinder Parts

Page A

 Fig # Img Part Name Availability Price
1Armature Assembly.
Part #: 623584-02SV
In stock
4 available
 $60.23
Add To Cart
2Field Case
Part #: 623599-00
In stock
2 available
 $8.47
Add To Cart
3Gear Case Assembly
Part #: 623586-00SV
In stock
12 available
 $31.01
Add To Cart
4Screw
Part #: 330065-31
In stock
25+ available
 $0.99
Add To Cart
5Arm
Part #: 648743-00
In stock
25+ available
 $1.99
Add To Cart
6Felt Seal
Part #: 623592-00
In stock
25+ available
 $0.99
Add To Cart
7Brush (Sold Individually)
Part #: 650916-01
Note: Sold Individually
In stock
25+ available
 $6.14
Add To Cart
9Brush Spring (Sold Individually)
Part #: 623589-00
In stock
25+ available
 $0.99
Add To Cart
10Cap
Part #: 623591-00
In stock
25+ available
 $0.99
Add To Cart
11Screw
Part #: 593685-00
In stock
21 available
 $0.99
Add To Cart
12Handle Set
Part #: 625243-01S
In stock
7 available
 $9.41
Add To Cart
13Switch
Part #: 641889-00SV
In stock
11 available
 $7.26
Add To Cart
16Cord Clamp
Part #: 636963-00
In stock
3 available
 $1.19
Add To Cart
17Screw
Part #: 330019-03
In stock
23 available
 $2.99
Add To Cart
18Cord Protector
Part #: 330005-01
In stock
25+ available
 $5.06
Add To Cart
Fig #ImgPart NameAvailabilityPrice
19Nut 5/8"
Part #: 636226-00
In stock
25+ available
 $8.61
Add To Cart
20Flange
Part #: 633257-00SV
In stock
25+ available
 $5.81
Add To Cart
21Guard
Part #: 628580-00
In stock
6 available
 $8.47
Add To Cart
24Power Cord - 8', 18 Gauge, 2-Wire
Part #: 330072-98
In stock
25+ available
 $12.95
Add To Cart
26Terminal
Part #: 623593-00
In stock
18 available
 $0.99
Add To Cart
27Spring
Part #: 628396-00
In stock
4 available
 $1.03
Add To Cart
29Nameplate
Part #: 629109-00
In stock
2 available
 $1.03
Add To Cart
30ID Label
Part #: 635892-00
In stock
2 available
 $1.73
Add To Cart
31Warning Label
Part #: 626891-00
In stock
14 available
 $1.03
Add To Cart
70Nut
Part #: 604484-00
In stock
7 available
 $2.99
Add To Cart
71Pinion
Part #: 623564-00
In stock
10 available
 $7.52
Add To Cart
72Bearing
Part #: 330003-60
In stock
12 available
 $5.21
Add To Cart
73Felt Seal
Part #: 623617-00
In stock
3 available
 $2.99
Add To Cart
74BRG. Retainer
Part #: 623580-00
In stock
3 available
 $1.87
Add To Cart
75Slinger
Part #: 623613-00
In stock
5 available
 $3.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
76Ball Bearing
Part #: 605040-02
In stock
16 available
 $4.25
Add To Cart
77Bearing Cup
Part #: 641823-00
In stock
14 available
 $1.99
Add To Cart
78Field
Part #: 624764-00
In stock
7 available
 $21.65
Add To Cart
79Fan Baffle
Part #: 623572-00
In stock
2 available
 $1.03
Add To Cart
80Screw
Part #: 330065-25
In stock
6 available
 $1.12
Add To Cart
81Gasket
Part #: 623618-00
In stock
13 available
 $2.99
Add To Cart
82Sleeve,Rubber
Part #: 611492-00
In stock
2 available
 $2.99
Add To Cart
83Gear Case Cover
Part #: 625414-00
In stock
2 available
 $1.03
Add To Cart
84Screw
Part #: 385676-01
In stock
25+ available
 $0.99
Add To Cart
85Screw
Part #: 631609-02
In stock
7 available
 $2.99
Add To Cart
86Terminal
Part #: 444262-00
In stock
25+ available
 $1.99
Add To Cart
87Wrench
Part #: 401680-00
In stock
22 available
 $9.11
Add To Cart
88Side Handle
Part #: N239381
In stock
20 available
 $10.69
Add To Cart
89Link
Part #: 626999-00
In stock
3 available
 $3.99
Add To Cart
90Bar
Part #: 644326-00
In stock
4 available
 $3.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
91Switch Button
Part #: 623608-00
In stock
6 available
 $3.99
Add To Cart
92O-Ring
Part #: 633044-00
In stock
10 available
 $2.99
Add To Cart
93O-Ring
Part #: 633043-00
In stock
25+ available
 $2.99
Add To Cart
Grease, 7LBS
Part #: 429954-00
Ships in 9 - 13 business days
 $217.87
Add To Cart
Grease,1 LB.
Part #: 429954-01
In stock
1 available
 $109.27
Add To Cart
846Shim
Part #: 5140030-98
Ships in 9 - 13 business days
 $1.19
Add To Cart
856Guard (Enclosed Top)
Part #: 643772-00
In stock
5 available
 $14.50
Add To Cart
861Kitbox
Part #: 651196-00
In stock
7 available
 $35.11
Add To Cart

Enter your engine's type number in this search field to show the parts that match your engine.

Your engine's type number is the second part of the model number stamped on your Briggs & Stratton engine (see picture).

Grinder Parts

Repair Articles

How to Replace the Gear Case on a DeWALT Angle Grinder (Model D28402)
How to Replace the Gear Case on a DeWALT Angle Grinder (Model D28402)

Replace your case. Step-by-step instructions show you how to quickly remove and install the gear case on a DeWalt grinder.
How to Replace the Bearing Cup on a DeWALT Angle Grinder (Model D28402)
How to Replace the Bearing Cup on a DeWALT Angle Grinder (Model D28402)

Simple steps to remove and install the bearing cup on a DeWalt angle grinder model D28402.
How to Replace the Pinion Gear on a DeWALT Angle Grinder (Model D28402)
How to Replace the Pinion Gear on a DeWALT Angle Grinder (Model D28402)

Pinion problems? This article shows you how to quickly remove and install a new pinion gear on a dewalt angle grinder.
How to Replace the Front Armature Bearing on a DeWALT Angle Grinder (Model D28402)
How to Replace the Front Armature Bearing on a DeWALT Angle Grinder (Model D28402)

Step-by-step guide for replacing the front armature bearing on a DeWalt D28402 angle grinder.
Repair Stories
Symptom:
No Power
Parts Used:
Part Number:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Entry Date:2013-10-08 12:59:38
10 of 10 customers found these instructions helpful
Motor brushes wore out, old switch was still working but was replaced as preventative measure
No special skill required for doing this repair. Remove lower part of housing and remove cord and cord clamp. Mark wires for correct replacement. Use small needle nose pliers to move leaf spring end from back of brush holder onto small molded pin provided - to take spring pressure off brush. A #6 torx bit is needed to remove the brush holder. New brushes come with friction connectors that fit through the hole in the brush holder. Replace brushes one at a time. A quick photo of the wiring packing around the cord clamp and switch might help in getting wires back into the case at the end.
Did these repair instructions help you?
Discussion
Discussion for the DeWALT D28110 Type 1 Grinder

Post a Comment
Login or signup to comment.
Login or signup to comment.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
55head69
Question: 28110 Grinder

55head69

How do I get the gear off of the head gear assembly?
WJA
Reply: 28110 Grinder

WJA

Hello 55head69,

If you are looking for the large bevel gear it can only be purchased as an assembly. part number 623586-00SV. To remove the 623564-00 pinion gear, take off the 6044484-00 nut and you should be good to go.

Hope this helps,
-WJA
Could someone please tell me how to properly replace the link and start button on a Dewalt D28110 grinder. The cases are split at the switch and the broken link has been removed. How do I install the new link and start button
1124044
Reply: Dewalt D28110 Link And Start But...

1124044

The link slides all the way up inside the main body and the new start button snaps into the long slot in the new link.
It is easier to follow the diagram above and lay your parts out like it. The switch
will only fit and work one way.....
If you need more help, contact me at
walterboswell@bellsouth .net.....
give me a day or 2 to respond.
dsdairy
Question: Dewalt D28110 Grinder

dsdairy

Does this grinder take one or two brushes? Figure #7 part # 650916-01. The picture shows one brush. But then the order form says, sold individually. I'd already ordered one.
Tinkerdave
Reply: Dewalt D28110 Grinder

Tinkerdave

Hi dsdairy,
The tool takes two brushes.Hope that helps.
Tinker
susswein
Question: Dewalt Angle Grinder Dead

susswein

I have 2 dewalt angle grinders that won't start (models D28110 and D28402). One of them is totally dead, the other will occasionally start for a split second, then die.

Any suggestions on what to look for when I open them up, besides checking the switch for continuity? Can you tell through visual inspection if the brushes are bad?
Hi all, this is my first post & I hope someone can help me out. I've got a DeWalt 4-1/2" angle grinder, model # D28110 to be exact, & I suspect the power switch is bad because one minute it was working fine & then it just wouldn't switch on. I've got a multimeter but I don't know how to go about testing the switch before I order a new one. I use this grinder in my job & am now relying on my 7" grinder but it's so heavy & the small one is fine most of the time so i'd like to get it going again soon. My next grinder will be a Metabo but until then any advice would be greatly appreciated.
UtahAV
Reply: Testing Power Switch On Grinder

UtahAV

Hi pirana,

First set your multimeter to test impedance (Ohm's). Make sure that the tool is unplugged. You will need to remove the housing so that you can access the switch. The switch will have four wires coming from it. The first thing you will need to determine is the path which the electricity follows through the switch. Many times there will be a diagram right on the switch. The power may flow through the switch front to back or side to side. First, with the switch off, hold the test leads on two opposite wires on the switch. If you still are not sure of the flow of power test front to back and side to side. At this point you should not get any reading anywhere on the switch. Now turn the switch on and do the same test. With the switch on you should get a reading across both sides of the switch. If you don't or if it is only on one side then the switch is bad and will need to be replaced.

I hope this helps!

-UtahAV
-Mark
pirana
Reply: Testing Power Switch On Grinder

pirana

Thanks Utah. I did as you suggested and it looks like it is indeed a bad switch.
UtahAV
Reply: Testing Power Switch On Grinder

UtahAV

You bet! Glad I could help.

-UtahAV
-Mark
Accessories
Accessories for the D28110

Backing Pads:
See more backing pads 
DW4945
Soft Rubber Backing Pad - 4-1/2" Diameter, 5/8-11 Arbor
$18.58

DW4939
Paper Backing Pad - 4-1/2" Diameter, 7/8 Arbor
$9.98

fancyboxy