Repair Forum     Repair Center    Blog
Sign In Support Shopping Cart
Authentic Parts
      Call us toll free 866-802-6383
9:00AM-8:00PM Mon-Fri, ET
9:00AM-6:00PM Sat, ET
Repair Parts Home    Power Tool Parts    Delta Parts    Delta Band Saw Parts    

Delta 28-276 14" 3/4HP Motor Open Stand Band Saw Parts

Delta 28-276 14 delta logo

 Delta 28-276 14" 3/4HP Motor Open Stand Band Saw Parts

Page A
Page B
Page C
   Page A   

 Fig # Part # Img Part Name Availability Price Qty
1905139
Knob
Knob Obsolete - Not Available
Discontinued
$0.00N/A
2905140
Nut
Nut
In stock
2 available
$1.65
3905141
Stud
Stud
In stock
1 available
$1.65
4905142
Guard
Guard
Ships in 16 - 22 business days
$41.14
51348294
Hex Nut
Hex Nut
Backorder:
No ETA.
$3.42
61348917
M12 Flat Washer
M12 Flat Washer Obsolete - Not Available
Discontinued
$0.00N/A
7907238
Wheel
Wheel Obsolete - Not Available
Discontinued
$0.00N/A
8920040107272
Bearing
Bearing
Ships in 16 - 22 business days
$24.39
9907019
Spring Clip
Spring Clip
Ships in 16 - 22 business days
$1.34
10905144
Spacer
Spacer
Ships in 16 - 22 business days
$1.65
11905145
Tire
Tire
In stock
2 available
$25.02
11A905146
Washer
Washer
Ships in 16 - 22 business days
$1.34
121246036
Cap Screw
Cap Screw
In stock
2 available
$7.53
131243502
Washer
Washer Obsolete - Limited Quantity
In stock
1 available
$1.46
14905147
Frame
Ships in 16 - 22 business days
$146.24
Fig #Part #ImgPart NameAvailabilityPrice
14A1234908
Insulator
Insulator
Ships in 16 - 22 business days
$0.86
14D905162
Lift Shoe
Lift Shoe Obsolete - Not Available
Discontinued
$0.00N/A
14E905161
Tension Crank
Tension Crank Obsolete - Not Available
Discontinued
$0.00N/A
14F1346071
Ext Ret Ring
Ext Ret Ring
In stock
2 available
$1.03
14G905163
Handle
Handle
In stock
3 available
$9.97
14H907360
Roll Pin
Roll Pin
In stock
3 available
$1.65
15905149
Stud
Stud
Ships in 16 - 22 business days
$4.98
16488822-00
Washer
Washer
In stock
2 available
$0.06
17905150
Screw
Screw
Ships in 16 - 22 business days
$1.65
18905150
Screw
Screw
Ships in 16 - 22 business days
$1.65
19905151
Guard
Guard
Ships in 16 - 22 business days
$38.49
19A330045-22
Screw
Screw
Ships in 16 - 22 business days
$1.05
201345893
Nut
Nut
In stock
1 available
$3.18
21905152
Shaft
Shaft
Ships in 16 - 22 business days
$6.01
22905153
Hinge
Hinge
In stock
8 available
$9.97
Fig #Part #ImgPart NameAvailabilityPrice
23905154
Pin
Pin
Ships in 16 - 22 business days
$2.08
24905155
Knob
Knob Obsolete - Not Available
Discontinued
$0.00N/A
25905156
Sliding Bracket
Sliding Bracket Obsolete - Not Available
Discontinued
$0.00N/A
261344333
Wing Nut
Wing Nut
Ships in 16 - 22 business days
$1.44
27905157
Thumb Screw
Thumb Screw
Ships in 16 - 22 business days
$2.08
28905158
Spring
Spring
Ships in 16 - 22 business days
$3.33
29904070115711
Fiber Washer
Fiber Washer Obsolete - Not Available
Discontinued
$0.00N/A
30905160
Nut
Nut
Ships in 16 - 22 business days
$2.08
31905164
Knob
Backorder:
No ETA.
$8.16
32905165
Guard
Guard
Backorder:
No ETA.
$9.97
331347527
Screw
Screw
In stock
2 available
$4.26
341310210
LockWasher
LockWasher
Backorder:
No ETA.
$1.11
35905166
Door Catch
Door Catch
In stock
2 available
$2.08
36905167
Hex Stud
Hex Stud
In stock
1 available
$2.08
371340637
Washer
Washer
In stock
1 available
$1.18
Fig #Part #ImgPart NameAvailabilityPrice
401243321
Screw
Screw
Ships in 16 - 22 business days
$2.61
43905168
Guard
Guard
Ships in 16 - 22 business days
$43.13
44905139
Knob
Knob Obsolete - Not Available
Discontinued
$0.00N/A
45905140
Nut
Nut
In stock
2 available
$1.65
46905141
Stud
Stud
In stock
1 available
$1.65
471343859
Nut
Nut Obsolete - Limited Quantity
In stock
2 available
$2.57
48905169
Wheel
Wheel
Ships in 16 - 22 business days
$72.01
49905145
Tire
Tire
In stock
2 available
$25.02
50905170
Washer
Washer
In stock
3 available
$1.65
51920040205348
Bearing
Bearing
In stock
2 available
$49.27
52905171
Key
Key
Ships in 16 - 22 business days
$2.08
53905172
Lower Drive Shaft
Lower Drive Shaft Obsolete - Not Available
Discontinued
$0.00N/A
54905173
Key
Key
Ships in 16 - 22 business days
$1.65
551347527
Screw
Screw
In stock
2 available
$4.26
561310210
LockWasher
LockWasher
Backorder:
No ETA.
$1.11
Fig #Part #ImgPart NameAvailabilityPrice
57905166
Door Catch
Door Catch
In stock
2 available
$2.08
58905167
Hex Stud
Hex Stud
In stock
1 available
$2.08
59905174
Base
Ships in 16 - 22 business days
$310.04
59A905175
Wire Clip
Wire Clip
Ships in 16 - 22 business days
$1.34
59B1342455
Screw
Screw Obsolete - Not Available
Discontinued
$0.00N/A
59C1342455
Screw
Screw Obsolete - Not Available
Discontinued
$0.00N/A
59D907018
Guard Obsolete - Not Available
Discontinued
$0.00N/A
59E901808
Wire Sleeve
Backorder:
No ETA.
$0.18
60905176
Dowel Pin
Dowel Pin
Ships in 16 - 22 business days
$1.34
65905177
Screw
Screw
Ships in 16 - 22 business days
$6.65
66905178
Washer
Washer
Ships in 16 - 22 business days
$2.08
67905179
Washer
Backorder:
No ETA.
$1.74
68905180
Hex Nut
Backorder:
No ETA.
$2.70
69905181
Spring
Spring
Ships in 16 - 22 business days
$1.65
701343859
Nut
Nut Obsolete - Limited Quantity
In stock
2 available
$2.57
Fig #Part #ImgPart NameAvailabilityPrice
711243321
Screw
Screw
Ships in 16 - 22 business days
$2.61
72488874-00
Washer
Washer
Ships in 16 - 22 business days
$0.88
73905182
Spring Clip
Spring Clip
Ships in 16 - 22 business days
$1.65
75905183
Screw
Screw
Ships in 16 - 22 business days
$2.08
76907017
Guard
Guard
Ships in 16 - 22 business days
$3.33
77A16208
Warning Label
Warning Label
Ships in 16 - 22 business days
$0.93
78911315
Plug
Plug
In stock
9 available
$1.28
79911316
Ball
Backorder:
No ETA.
$1.28
801246133
Set Screw
Set Screw
In stock
2 available
$2.52
81642226-00
Hardware Pack
Hardware Pack
Ships in 16 - 22 business days
$26.47
629488813-00
Lock Washer
Lock Washer Obsolete - Not Available
Discontinued
$0.00N/A

Enter your engine's type number in this search field to show the parts that match your engine.

Your engine's type number is the second part of the model number stamped on your Briggs & Stratton engine (see picture).

Saw Parts  Band Saw Parts

Repair Articles

How to Diagnose a Bad Power Cord or Switch
How to Diagnose a Bad Power Cord or Switch

This article outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test tool and appliance cords and switches, the two parts usually responsible for electri...
How to Change a Bandsaw Blade
How to Change a Bandsaw Blade

Changing a bandsaw blade only takes minutes with the help of this article's professional power tool tips, including proper bandsaw blade guide adjustment.
Bandsaw Tire Replacement
Bandsaw Tire Replacement

This article gives step-by-step instructions to loosen new bandsaw tires for easier installation.
Power Tool Care and Maintenance 101
Power Tool Care and Maintenance 101

This article suggests guidelines for power tool care and maintenance. It also describes information tools available at eReplacementParts.com.
Repair Stories
Symptom:
Broken Trunnions
Parts Used:
Part Number:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Entry Date:2013-12-13 10:31:41
5 of 5 customers found these instructions helpful
Both trunnions on the tilt table had fallen apart
Delta had the trunnions on back order so I used the jet part number 100042. The fit just right. I found that a 10mm wrench and 10mm socket wit short extension and ratchet and a 6\" square were all the tools I needed.
Unbolt the trunnions from the table (if like on my unit the trunnions were not intact so this was unnecessary) lift the table and rotate it so the blade could pass through the slot in the table normally used for blade changes. Place table hold down bolts into the trunnions(two different lengths -get them right) bolt on the new trunnions but do not tighten, place the table back on the saw and install table knobs loosely now see that the table moves freely and tighten the trunnion bolts.
Now align the table as per instruction manual.
It should be noted that the aftermarket parts do not allow for the tilt scale to be installed, I can live with out mine.
Did these repair instructions help you?
Discussion
Discussion for the Delta 28-276 14" 3/4HP Motor Open Stand Band Saw

Post a Comment
Login or signup to comment.
Login or signup to comment.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
1221718
Question: Shaft

1221718

is there any specs on size for this part? I have a
Taiwan knockoff a friend gave me and I need the shaft and bearing.
WJA
Reply: Shaft

WJA

Hello 1221718,

Unfortunately the manufacture does not provide any specs on the 905193 Shaft. If we had stock of this part I would have been glad to give them to you. The Taiwan knockoffs did a pretty good job of copying most of the parts of these saws, so it's a good bet that it will work.

-WJA
wilkens
Question: Motor Contacts

wilkens

can i get just the contacts for the motor,, have had to file them numerous times.. motor is still good. just need contacts
WJA
Reply: Motor Contacts

WJA

Hello wilkens,

Delta does not provide internal parts for this motor. You may want to take your motor to an electric motor service shop in your area, to see if they can help you.

-WJA
kelliottjohnson
Question: Bandsaw Table Trunion

kelliottjohnson

Recently moved my shop to another state. Went to use my saw and the table fell off. Turns out the trunions holding the table had disintegrated into many small pieces. It is very thin and flimsy cast material. There appears to be no replacement part available. Any suggestions? This seems to be a manufacturing fault.
WJA
Reply: Bandsaw Table Trunion

WJA

Hello kelliottjohnson,

Powermatic uses the same style trunnion on their bandsaw. It is part number PWBS14-144. It is probably made from the same material but at least it will get your saw working again.

-WJA
bjenkins
Question: Trunions

bjenkins

I was shocked when I moved my bandsaw back into its corner and the table came off in my hands. I was absolutely stunned when I took it off, turned it over and was able to break the cheap cast trunions into pieces with my fingers.

I consider this a serious design flaw, something I don't expect from Delta.

Questions:

1. Are the replacement trunions sturdier and stronger than the original?

2. Shouldn't Delta have recalled them and given us replacements for free?
drussel3
Question: Bore

drussel3

Is the bore of this part 0.788" (20 mm), and does it have a keyway?
PATRICKCUES
Question: TRUNNION

PATRICKCUES

Anyone know where I can get one of these now?

Thanks
WJA
Reply: TRUNNION

WJA

Hello PATRICKCUES,

You may want to try the Jet trunnion. As I remember the bolt holes do line up but the thickness of the metal maybe a little different. Here is a link to the part number.

Jet Trunnion 100042.

Hope this helps,
-WJA
mike190
Reply: TRUNNION

mike190

still looking for one? gimme Ereplacement part number and i'll look....I have a lot of spare parts: doors table complete lower casting(s); etc email h92543 at yahoo dot com
jumahl
Question: Bandsaw Trunnions

jumahl

I have been without the use of the second Delta bandsaw I bought specifically for one operation only in my small production shop in order to avoid frequent blade changes, for nine months now, since May of last year. So my $800 dollar investment sits useless and I have to switch blades on my other bandsaw anyway. Does Delta ever intend to support their product? And while we're on the subject, why make such a critical part from an extremely thin zinc casting? Is Delta trying to drive customers into the arms of other manufacturers?

Sincerely,
Disgusted
mike190
Reply: Bandsaw Trunnions

mike190

still looking for one? gimme Ereplacement part number and i'll look....I have a lot of spare parts: doors table complete lower casting; etc email h92543 at yahoo dot com
scottn
Question: Trunnion

scottn

Both of these just crumbled today. Any idea when they might be available.
WJA
Reply: Trunnion

WJA

Hello scottn,

Unfortunately the trunnions you need are on a factory back order, with no delivery date. Which means the manufacture cannot give us a date when they will be available.
We do update our system daily so keep checking with us for a delivery date on these items.

-WJA
James A. Hutchins
Question: Manual Replacement.

James A. Hutchins

Do you have service manuals for the Mod.#28-276?
tim
Question: Setup Information

tim

Where can I find manuals for a 28-276 Delta bandsaw? I bought a display model which doesn't have any manuals. Also what type and size of blades does this saw use? Any information will greatly be appreciated.

Thanks

Tim
Frenchman1
Reply: Setup Information

Frenchman1

Blades 93-1/2" fit this saw. Widths from 1/8" to 1" will work depending on the radius of
cut you want to make
ely barnes
Question: Model 28-276

ely barnes

Can I extend the height of the unit?
fancyboxy