How to Fix a Lawn Mower Carburetor
This article will help teach you the process of properly maintaining and repairing a lawn mower carburetor.
How to Replace the Spark Plug on a Honda HRX217 Lawn Mower
This article will walk you through the steps of removing, inspecting, and replacing the spark plug in your Honda HRX217.
How to Test a Small Engine for Spark
If your small engine isn't starting, you'll need to diagnose many issues including the spark plug. This video walks you through the steps of how to test for a spark using a spark tester.
Quick Fix: How to Sharpen the Blade on your Lawn Mower
Maintaining your lawn just got easier. The steps outlined in this article will serve as a guide to replacing or sharpening the existing blade on your lawnmower.
Discussion for the Black And Decker MM275 18" Electric Mulching Mower
Post a Comment
Ask a question, answer a question, or post a comment!
Reply: Mower Bag
I know that the BA-075 Grass Bag has been discontinued for quite a while now. Your best bet is to keep searching on line, hopefully some will have one out there.
Reply: Hardware Bag
Most hardware bags that I am familiar with, contain the nuts,bolts,washers etc to put the machine together. If you have a lot of those kind of parts missing. That would be the way to go.
Question: Push Ring Removal
How do you remove a push ring to replace a wheel or flap guard on a Black and Decker Cordless Electric mower.
Reply: Push Ring Removal
Really they should be used only once and replaced with a new one.I just grab it with a pair of channel locks and twist it off.If you want to use the old one you can sometimes rock them back and forth while pulling and this will often get them off.Hope that helps.Good luck.
Reply: How To Replace Flap
I am in the same situation. It appears the flap slides only in one way, but the wheel with the lever is in the way. So far, I has been unable to remove the wheel, which appears is the actual problem because of the unusual nut/washer combination.
Question: Switch P. Button MM275 Mower
What wires attach to the posts on the P. Button Switch?
Reply: Switch P. Button MM275 Mower
If you contact a Dewalt Factory Service Center, they might be able to explain to you over the phone. or send you an e-mail diagram.
Hope that helps,
Can someone give me the correct location of the four wires for MM275
Looking at the rectifier you should have + on the right.That connects to the red motor wire.Black - on the left connects to to the red and black wire.Yellow AC on the top goes to black wire and ac yellow on bottom goes to the orange wire.Hope that helps.Good luck.
Question: Runs A Few Turns Then Stops
I turn the machine on and after a few revolutions it seems to jam shut. When moving the blade physically it runs again and then stops cold again. Any suggestions?
Reply: Runs A Few Turns Then Stops
I had the problem of the motor jamming. I opened up the mower, unscrewed the motor, loosed the cord mounting, unscrewed the top of the motor and inspected the magnet ring. It was shattered. I am ordering a new one now.
Question: On Off Switch
When I squeeze the lever to run my machine it starts and stops intermittently. The switch is worn. What part do I order?
Reply: On Off Switch
My model MM275 has an intermittant working on & off switch. If I squeeze the handle hard and pull it to the right it works. Otherwise, it continues to work on & off. What parts do I need. Also, what will help the cord to stay plugged in. It has a tendancy to fall off as the coed hangs down from the plug.
Question: MM275 Stopped Working
I have a B&D MM275 that stopped working. I'm afraid that's the only symptom. It was as if I unplugged it, but the power cord to the mower works fine. It just stopped.
Any suggestions about what might be the problem?
Reply: MM275 Stopped Working
It sounds like the button on your switch is worn and what happens, your handle no longer hits the button, causing the mower to quit running. After you pull the handle up, hit the switch with your hand. This will cause the handle to move slightly and will most likely start the mower. It will not stay running. I say this as I had the same problem and bought a new switch. My mower now runs fine.
Reply: MM275 Stopped Working
There is a part called a "rectifier" at the very top of the lawn mower inside the case that holds 4 little wires, some black and some red. We've had to replace that part (about $3.00 apiece) a few times. The lawnmower ran fine after we did that. Hope it works for you. Check the parts "blow-up" above for added location information.
Question: Wiring Order
I have a B&D mm275, the push button switch melted, I have a new one but am not sure of wiring.
It is 4 prong, red, from motor, black from motor, white from motor, black from inlet plug. All were melted off.
Reply: Wiring Order
I can text you photo of the switch and wires for $1 by paypal to cover my time to take it apart.