Hard
30-60 minutes
This Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually.
rnrn
rn
Ball Bearing 629ddw 211092-6
OEM part for: Makita
Part Number: 211092-6
$15.11
In Stock
Ships within 1 business day 
Jump To:
Product Description ?
rn
- Classification: Part
- Weight: 0.05 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This Ball Bearing 629ddw will fit the following 80 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Makita
Show More Compatible ModelsThis item works with the following types of products:
- Router Parts
- Vacuum Parts
- Sander Parts
- Band Saw Parts
- Saw Parts
- Blower Parts
- Grinder Parts
- Plate Joiner Parts
- Multi-Tool Parts
- Chain Saw Parts
This part replaces obsolete part #: 210078-7
Repair Videos ?
Watch the Repair Video for
Ball Bearing 629ddw
Customer Part Reviews ?
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Ball Bearing 629ddw
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
lower bearing frozen
George - February 3, 2017
👍 2 of 2 people found this instruction helpful
Tool Type
Sander
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, bearing puller
Parts Used
As many woodworkers know, power tools made ten plus years ago are better than new one's, so if you can find the parts..there is value in fixing it yourself. Disassembly of this Makita sander is easy - just be sure you have several sizes of Phillips head screw drivers on hand - those factory installed screws are in there tight - don't strip them. Pretty easy diagnostic- the lower bearing was frozen - getting it off the spindle takes a little work - go easy. Putting the new bearing is simple - just be sure it is seated all the way on to the shaft. Take your time with the reassembly - be sure the brushes are seated correctly and the shaft turns freely. Since many of the housing and internal pieces are plastic don't force them - be sure they are lined up correctly before tightening all the screws. $15.00 and my favorite sander is back in action. Good luck to you on your project.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
An old sander that had a bad bearing and ruined brushes.
Ricky - July 21, 2019
Tool Type
Sander
Difficulty
Expert
Time
1-2 hours
Tools Used
Screwdriver, Socket set, hammer
had to take the sander completely apart. The brushes were an easy fix. It was tough to get the old bearing off the shaft and set the new bearing on the shaft. It took some ingenuity and a loy more time than i expected. The bearing was an exact fit. Thank goodness for the right parts. The sander is now ready for the next 40 years.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bearing was bad on Makita BO4510 sander purchased at a yard sale
DOUGLAS - February 25, 2019
Tool Type
Sander
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Wrench Set, Nutdriver, gear puller
1. Dismantled sander to determine which bearing was bad.
2. Found the bottom motor bearing was bad
3. Removed the armature and used a small gear puller to remove the bad bearing
4. Pressed the replacement bearing in the shaft using a deep socket and hammer
5. Removed the seals on the remaining bearings and re-packed them with low viscosity grease
6. Replaced worn brushes
7. Reassembled the sander and tested it.
8. Now I have a sander that runs like new.
2. Found the bottom motor bearing was bad
3. Removed the armature and used a small gear puller to remove the bad bearing
4. Pressed the replacement bearing in the shaft using a deep socket and hammer
5. Removed the seals on the remaining bearings and re-packed them with low viscosity grease
6. Replaced worn brushes
7. Reassembled the sander and tested it.
8. Now I have a sander that runs like new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
