Easy
15-30 minutes
This is an authentic Coleman replacement assembly made for some camp stoves. This assembly acts as the generator and valve. A generator atomizes fuel and mixes it with air, so that it can be ignited. The valve controls the flow of fuel through the generator, adjusting the strength of the flame.
This Assembly Includes the Following Parts:
• Fuel Tube, Part Number: 426-5021
• Generator, Part Number: 426-5621
• Valve Assy, Part Number: 426-6561
• Gas Tip, Part Number: 426-2181
• Knob Assembly, Part Number: R413-149T
• Direction Disc, Part Number: 201-172
• Screw, Part Number: 1146B0406
Valve & Gen 4266611
OEM part for: Coleman
Part Number: 4266611
$85.94
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Product Description ?
- Classification: Part
- Weight: 0.41 lbs.
- Shipping: Ships Worldwide
Compatibility
This part will fit the following 2 machines
Coleman
413H499 2 Burner Gas Camp Stove View Diagrams & Manuals
426E499 3 Burner Gas Camp Stove - Coleman Fuel View Diagrams & Manuals
This item works with the following types of products:
- Range Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Valve & Gen
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Generator was leaking
Kim - August 25, 2016
👍 2 of 2 people found this instruction helpful
Tool Type
Range
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Adjustable Wrench
Parts Used
I removed the old generator and replaced it with the new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Fuel shutoff valve was leaking under pressure from being over tightened.
Jeff - April 6, 2021
Tool Type
Range
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Adjustable Wrench, Gas rated (grey) thread seal tape
Parts Used
*These instructions presume there is still some liquid fuel in the tank as it is not possible to fully drain the tank due to a recessed fill tube. Be careful to keep tank oriented with the valve upright to avoid spilling fuel during the repair. Take precautions to clean any spilled fuel and remove any source of ignition from the work area. Ground yourself to a light switch or metal appliance to discharge any static as this could also ignite fuel vapors. Have a fire extinguisher near by that is in good working order before beginning the repair.
1. Vent vapor pressure from fuel tank and clean any dirt or debris from the tank.
2. Clean thoroughly around thread fitting where the valve assembly enters the tank.
3. Use the adjustable wrench to turn the old valve assembly counterclockwise two full turns.
4. Clean any loosened factory pipe dope from valve fitting before further removing from tank.
5. Carefully clean any remaining pipe dope from internal threads of tank after removing valve.
6. Install two wraps of new thread seal tape onto new valve threads in a clockwise direction.
7. Install valve assembly into tank until snug then an additional turn to orient the generator.
8. Lightly close valve knob, tank cap, and pump 35 full strokes of air into the tank.
9. Invert tank and carefully observe for 5 minutes to ensure there are no fuel leaks.
10. Release pressure and store tank and range as per manufacturer instructions.
1. Vent vapor pressure from fuel tank and clean any dirt or debris from the tank.
2. Clean thoroughly around thread fitting where the valve assembly enters the tank.
3. Use the adjustable wrench to turn the old valve assembly counterclockwise two full turns.
4. Clean any loosened factory pipe dope from valve fitting before further removing from tank.
5. Carefully clean any remaining pipe dope from internal threads of tank after removing valve.
6. Install two wraps of new thread seal tape onto new valve threads in a clockwise direction.
7. Install valve assembly into tank until snug then an additional turn to orient the generator.
8. Lightly close valve knob, tank cap, and pump 35 full strokes of air into the tank.
9. Invert tank and carefully observe for 5 minutes to ensure there are no fuel leaks.
10. Release pressure and store tank and range as per manufacturer instructions.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Poor performance
Joel - August 19, 2019
Tool Type
Range
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Nutdriver, Adjustable Wrench
Used the parts list diagram provided when purchased
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
