*This part replaces obsolete part #: 322-451.
Product Information
Description:
This is a genuine Hitachi replacement part, it is sold individually. This is the Right Side Switch Handle half for the miter saws shown below. With the use of the 321-382 Left Switch Handle Half it secures the on/off switch in place. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
the 8 compatible machines
Products Compatibility
This item works with the following types of products:
- • Saw
Questions & Answers for Switch Handle (right Side)
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
1 of 1 people found this instruction helpful
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Wire stripper/crimper
Jobsite miter saw was dropped breaking the carry handle
Removed screws on broken handle/housing to expose wiring harness. Unhooked wires to feed through housing. Pulled harness from housing, and removed inner most handle/housing. Replaced broken parts, and reattached wiring. Also removed and replaced broken trigger handle assembly and fitted new safety switch. Replaced all screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Power Drill
Broken handle an guard
Just removed broken parts an replaced with new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
The handle was broken off by a fall during transport
Removed the broken pieces to inspect what needed replacement.
Looked up the saw on replacement parts. Com
Found the needed parts in the breakdown.
Went to the corresponding number below.
Ordered the party. When they arrived in must a few days, I installed them by installing the switch into the new handle pieces and installed the three screws to hold the handle onto the saw.
Job complete. Saw is as good as new.
Looked up the saw on replacement parts. Com
Found the needed parts in the breakdown.
Went to the corresponding number below.
Ordered the party. When they arrived in must a few days, I installed them by installing the switch into the new handle pieces and installed the three screws to hold the handle onto the saw.
Job complete. Saw is as good as new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Power Drill
Broken handles & trigger
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Miter saw fell down off its stand and broke the plastic handle. 3rd time in 12 years
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
I broke the switch handle when I dropped the saw
Removed two sides of the switch handle and switch. Replaced with new parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Handle assembly broken.
Replaced the handle assembly. Very easy to do.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Handle was broke
1. Removed the 3 screws.
2. Took the broken handle off.
3.Put the new handle on (making sure all the wires and the trigger were in place).
4. Put the 3 screws back in.
2. Took the broken handle off.
3.Put the new handle on (making sure all the wires and the trigger were in place).
4. Put the 3 screws back in.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Nutdriver
Both handles were broken and switch was defective
Installed two carbon brushes.
Installed new switch and replaced two handles, left and right,
Installed new switch and replaced two handles, left and right,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Miter Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Broken handle and switch
Removed broken parts installed new. Pretty straight forward replacements.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
2 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Hitachi handle replacement.
The part is a godsent which will allow for this great tool to go back into service after sitting idle for months. The shipping packaging was fine, but the lead time seemed excessive.
Guest -
March 14, 2024
Verified Purchase
Part fit like a perfect piece, no problems
Had accident, called E Replacement, we together got the pieces figured out and they came safely undamaged in a few days, everything fit like new and tool is back working like new, what more can you ask for, I’ve ordered a few times now and have always had satisfaction with E Replacement
Guest -
June 17, 2023
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information