Watch The
Repair Video

Spring-Governor

Part Number: 796260

1 Reviews

Order within the next 13 hours

and your part ships today!

Questions & Answers

Repair Instructions

*This part replaces obsolete part #: 260695 and 692208.

Product Information

Manufacturer: Briggs and Stratton, Toro

Product Number: 796260

Classification: Part

Weight: 0.01 lbs.

Shipping: Ships Worldwide

Description:

The governor spring is made out of metal and helps to control the speed of the engine. This authentic item is supplied directly from the original equipment manufacturer for use with Briggs & Stratton generators and Toro snowthrowers, tillers, and blower-vacuums. If it becomes lost or broken it will need to be replaced. A nutdriver may be necessary to help replace this part which is sold individually.

Warning: California's Proposition 65

Frequently Purchased With

Carburetor Dia..
$3.82

Intake Gasket..
$3.82

Air Cleaner El..
$8.61

Link--Mechanic..
$8.49

Spring-Governo..
$7.29

Compatibility

This part is compatible with the following machines:

Briggs and Stratton

8799-1 Portable Generator

Toro

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Blower
• Generator
• Snowblower
• Vacuum

Questions & Answers

Sort by

how do I bring up the repair instructions for replacing the gov. spring?

Elwood for model number 130212 asked on 2021-09-02

Hello Elwood, thank you for your question. Before you begin, make sure your engine has cooled. You should remove the wire and boot from the spark plug to prevent the engine from accidentally starting we recommend performing this procedure with little or no fuel in the tank. Loosen the rope guide wing nut and remove the starter rope use a 5/16 inch socket or nut driver to unthread the bolts securing the blower housing cover. Lift off the cover, lift the fuel tank off of the housing, note the orientation of the governor spring and detach the old spring. Install the new governor spring by hooking the short end onto the bracket and the long end on to the governor lever. Realign the fuel tank tabs with the slots in the blower housing and snap the tank into place. Replace the blower housing cover then thread and tighten the bolts to secure. Depress the bail arm, extend the starter rope, and hook the rope on the guide. Tighten the rope guide wingnut. With the repair completed reattach the wire and boot to the spark plug. We hope this helps!

Did this question help you?

I took my gov apart and am not sure I even had one but I can't imagine that I shouldn't have a spring to retrieve the throttle linkage. My problem is where does it go in the gov assembly, Thank you, Vern Barber

Vern Barber for model number 255707-0112-01 asked on 2019-08-07

Hello Vern and thank you for writing Here is the link to the diagrams . The spring governor is # 201 and yes most units have them. Hope this helps

Did this question help you?

Repair Instructions: Submitted by Customers Like You

1 of 1 people found this instruction helpful

Tool Type:

Lawn Mower

Parts Used:

Spring-Governor - 796260

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Nutdriver

Engine rpm erratic

1. Removed governor plate from engine.
2. Removed old governor spring & attached new one. Make sure to note where and how old spring was attached.
3. Reattached governor plate.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Spring-Governor - 796260

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, Wrench Set

I had Lost the spring

removed gas tank and carburetor.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Spring--Governor Link - 691842

Spring-Governor - 796260

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Pliers, Socket set, Needle nose pliers

Engine surging would only run on choke

Removed plastic top cover
Removed throttle assembly from side of motor
Replaced old spring between governor and throttle linkage.
Adjusted governor

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Screw (Regulator) - 690297

Spring-Governor - 796260

Spring-Governor Link - 690545

Spring-Pump Diaphragm - 692206

Repair Difficulty:

Medium

Time Spent Repairing:

More than 2 hours

Tools Used:

Screwdriver, Pliers, Power Drill, Socket set, Wrench Set, Nutdriver, Adjustable Wrench, Everything in tool box, minus the lumber crayon

1975 engine. Multiple parts missing or broken

Took some parts off another old engine, bought new parts from this excellent company. Installed some parts correctly, some incorrectly. Thought about it a lot, spent a lot of time looking at the parts diagrams on this site, finally got it right.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Spring-Governor - 796260

Carburetor Diaphragm - 270026

Spring-Governor Link - 690498

Air Cleaner Element - 27987S

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Nutdriver, Adjustable Wrench

Parts needed replacing

Put in new diaphragm & air cleaner, governor springs for fuel system.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

1 Reviews

Click to filter by ratings:

5 stars

4 stars

3 stars

2 stars

1 stars

Sort by:

Highest Rating
Most Recent

< PREV

NEXT >

Easy to install..

https://dfw.cbslocal.com/video/5652296-full-interview-with-texas-gov-greg-abbott-following-legislative-session/

Guest - June 22, 2021 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

NEXT >

Product Information

Manufacturer: Briggs and Stratton, Toro

Product Number: 796260

Classification: Part

Weight: 0.01 lbs.

Shipping: Ships Worldwide