This part is an OEM from Norge, Admiral, Magic Chef, Maytag, Crosley, Amana, Hoover, Jenn-Air, and International Washers. The snubber ring fits between the leg and washer base to reduce noise and vibration. The most common reasons for replacing the snubber ring is if the washer shakes a lot during use; loud noise during operation. This part is sold individually. Here is a list of tools that are needed to replace the snubber ring a short flathead screwdriver, flathead screwdriver, Phillips screwdriver, 1/4” nut driver, 5/16” nut driver, 3/8” nut driver, putty knife, locking pliers, slip joint pliers, ratchet with extension and a 3/8” socket.
Snubber WP21002026
OEM part for: GE, Maytag, Admiral, International, Amana, Jenn-Air, Norge, Crosley, Magic Chef, Hoover
Part Number: WP21002026
Compatibility
This part will fit the following 655 machines
Maytag
Admiral
International
Amana
Jenn-Air
Norge
Crosley
Magic Chef
Hoover
This item works with the following types of products:
- Washer Parts
- Saw Parts
This part replaces obsolete part #: 21002026
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Snubber
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Excessive vibration
Tool Type
Washer
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Power Drill, Socket set
Parts Used
2. Disconnect drain and other hoses.
3. Disconnect springs.
4. Remove tub and invert and place on a towel or padded surface on the ground.
WARNING....Brake assembly has loaded spring!! The following step ensures the brake spring will not unload and drill you in the face.
5. Remove only 2 mounting screws from the brake assembly and replace with longer screws of same thread type leaving approximately 1/4 inch gap between head of fastener and surface of brake.
6. Remove remaining fasteners from brake.
7. Remove snubber ring.
8. Clean surfaces around where ring goes on the brake and around the seating surface on the washer. Vacuum away shavings and use wet cloth with mild detergents only. Do not use lubricants of any kind on the new snubber ring.
9. Replace ring and secure brake with 4 open fasteners.
10. Remove 2 holding screws and replace with proper mounting screws left over from original group.
NOTE1......For machines that have been in service for a while say greater than 5 years advise replacing tub springs as well.
NOTE2.....Clean or replace hot and cold water filter cones and closely inspect hoses as well as drain hose for cracks or issues. Replace as required.
11. Reassemble in opposite order than prescribed for disassembly above. Don't forget to reconnect all hoses and properly secure with hose clamps.
WASH AWAY!!!!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.