Sleeve Bearing 42-40-0580

Snap Ring - 34-60-1400

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Pliers, # 30 torx, snap ring pliers

bad sleeve bearing, wobblie drive wheel

Remove blade pulley cover, remove snap ring and pulley hub washer. Use a 1/4" drive 9/16 socket to press / push old sleeve out, press new ones in. Put it back together in reverse order.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

4 of 4 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Wrench Set, SNAP RING PLIERS, Torx head wrenches

Portaband saw started throwing it's blade

Noticed a wobble in the wheels, so I ordered all the "suspect" parts I thought could be related to the problem.
1- Remove the Idler and Drive wheels
2- Drive the sleeve bearings out of the wheels and replace with new. I mic'd the axles and found they did NOT need replacement.
3- Replaced the rubber tires on each wheel
4- Reinstalled the wheels and replaced blade.
5-Test ran the saw, and blade ran true!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

3 of 3 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Snap Ring - 34-60-1400

Blade Guard - 43-54-0245

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Hammer

Bearings worn out

Knock out old bearings and replaced with new ones. Replaced the guard, snap ring and washers, with new pulley tire and put back together. Like new

Did you find this story helpful?

Thanks for voting and helping fellow customers!

3 of 3 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Blade Pulley - 28-95-0120

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

, SNAP RING PLÎERS , BUSHING INSTALLER , HAMMER , TORQUE BIT .

BLADE CAME OFF . BUSHING BAD IN PULLEY

REMOVE BLADE ,REMOVE 3 TORX SCREW FROM THE PULLEY HUB, REMOVED THE SNAP RING , AND THE PULLEY WASHER. I THEN REMOVED THE PULLEY. INSTALLED NEW BUSHINGS IN THE PULLEY & LUBED, ASSEMBLED IN REVERSE ORDER . I ALSO REPLACED THE OLD PULLEY TIRES WITH NEW ONES.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 2 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Snap Ring - 34-60-1400

Chain Sprocket Kit - 14-46-1175

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

, Snap ring pliers,allen wrench

Bandsaw chain and sprocket worn out, bad sleeve bearing and missing snap ring

Removed the blade pulley cover
Removed the blade pulley and sleeve bearings
Installed the new chain and sprocket assembly
Installed the new bushings, the blade pulley, washer and the new snap ring
Installed the blade pulley cover

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Chain Sprocket Kit - 14-46-1175

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Sleeve bearing worn and sprocket teeth broken.

Replaced sleeves in hub.
Replaced sprocket and chain.
Greased the chain and bearings.
Reassembled.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Band Saw

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Torks driver

Worn bushing & blade pully tire

Pressed out old bushing & replaced applied grease to shaft.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Band Saw

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set, Arbor press, torx bits, snap ring pliers

Drive wheel was wobbly.

1. Ensure saw is unplugged and remove blade.
2. Remove wheel with worn bushings by removing torx bolts and snap ring.
3. Use a suitable sized socket to press out bushings.
4. Press in new bushings with vise or Arbor press.
5. Reinstall wheel with new plastic washers.
6. Install blade, test, and adjust tracking, if necessicary.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Band Saw

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set

bandsaw blade kept popping off tool

I replaced the sprocket, chain, washers and bushings + replaced the rubber trucks and it works like brand new. It is a handheld Milwaukee bandsaw works great, probably for another 8 years. 60$ in parts vs 400$ for a new one. Watched a video

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Band Saw

Parts Used: