Medium
1-2 hours
It is an authentic Bosch item that is supplied by the original manufacturer for use with table saws. This is an identical replacement for a faulty or a missing hardware that was installed on a new unit. It is utilized to secure the cap to the motor cover. To ensure the exact location and the correct application of this screw, check the diagrams for your model. Keep in mind this high-quality component is made of durable metal and is sold as an individual item. A screwdriver will be needed to secure or remove it.
Screw 2610998571
OEM part for: Bosch
Part Number: 2610998571
$3.99
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 12 machines
Bosch
4000 (0601476139) Table Saw View Diagrams & Manuals
3915 (0601475039) 10 Inch Slide Miter Saw View Diagrams & Manuals
B3915 (0601475035) 10" Slide Miter Saw View Diagrams & Manuals
4100 (0601B13010) Table Saw View Diagrams & Manuals
4100DG-09 (0601B13010) 10" Worksite Table Saw View Diagrams & Manuals
4100DG-09 (3601L13010) 10" Worksite Table Saw View Diagrams & Manuals
4100-09 (0601B13010) 10" Worksite Table Saw View Diagrams & Manuals
4100-09 (3601L13010) 10" Worksite Table Saw View Diagrams & Manuals
GTS 10 XC (3601L30440) Table Saw View Diagrams & Manuals
GTS 10 XC (3601L30490) Table Saw View Diagrams & Manuals
GTS1041A (3601M13510) Table Saw View Diagrams & Manuals
GTS 10 J (3601M30530) Table Saw View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Saw Parts
- Table Saw Parts
- Miter Saw Parts
This part replaces obsolete part #: 2610911926
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
GENUINE PART,WORKS AS EXPECTED.
LIKE I SAID ABOVE RIGHT PART WORKS AS EXPECTED.
Guest -
April 6, 2022
Verified Purchase
Bosch 4900 Table Saw Speed Control and associated parts.
I ordered and received a Bosch 4900 table saw speed control board, various screws, brush kits and bearings. Speed Control identical to bad board, worked fine. It was a bit difficult tracking parts, as apparently some parts were delayed which delayed entire order. Exploded view helpful, but unclear when zoomed in. Even so, I felt 5 stars are in order!
Guest -
December 24, 2021
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Screw
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Front Bearing in motor blew up. I replaced both bearing even though there was nothing wrong with the rear bearing.
Rick - April 22, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, Adjustable Wrench, Dewalt 12V Impact Driver
1, Removed end cap from motor
2. Remove outer plastic case.
3. Removed plastic blade housing cover.
4. Removed front metal gear assembly cover.
5. Removed Armature from gear housing.
6. Used bearing puller to remove front bearing
7 Used Large 1/2 drive socket to install new bearing
8 Removed & replaced front rubber ring seal
9. Remove and replace rear bearing.
10. Cleaned gears and housing.
11. Repacked axle grease around gears, bearing and inside housing
12. Reassembled in the reverse order.
Note: The hardest part of this is reinstalling the two screws that hold the armature assembly to the front gear housing. There is a metal plate that the two screws that go through the housing into the metal plate on top of the armature. That plate is free-floating and there is about a 1/4" of clearance between the housing and the plate and the top of the armature assembly. Gravity is your enemy trying to get the plate and the screw to line up because there is NO room to put a screwdriver tip or anything inside the space. I tried for over an hour to get one of the screws started again with no success. Finally I went to my screw bin and found a 2" screw the same size and thread pattern as the original and use my scratch awl to line up one side of the plate to the hole. I use the long screw in the opposite side of the plate to temporarily screw it in and bring the plate to the top, where it was supposed to be, then removed the scratch awl, and put in one of the original screws and tightened it. Then I was able to remove the long screw and put the other original screw in the other side. After that was done I tightened both of the original screws and and rest took about 15 minutes. Maybe this will help someone else in doing this bearing replacement?
This repair was on a Bosch Model 4100 table saw, which by the way is a GREAT saw!
Rick
2. Remove outer plastic case.
3. Removed plastic blade housing cover.
4. Removed front metal gear assembly cover.
5. Removed Armature from gear housing.
6. Used bearing puller to remove front bearing
7 Used Large 1/2 drive socket to install new bearing
8 Removed & replaced front rubber ring seal
9. Remove and replace rear bearing.
10. Cleaned gears and housing.
11. Repacked axle grease around gears, bearing and inside housing
12. Reassembled in the reverse order.
Note: The hardest part of this is reinstalling the two screws that hold the armature assembly to the front gear housing. There is a metal plate that the two screws that go through the housing into the metal plate on top of the armature. That plate is free-floating and there is about a 1/4" of clearance between the housing and the plate and the top of the armature assembly. Gravity is your enemy trying to get the plate and the screw to line up because there is NO room to put a screwdriver tip or anything inside the space. I tried for over an hour to get one of the screws started again with no success. Finally I went to my screw bin and found a 2" screw the same size and thread pattern as the original and use my scratch awl to line up one side of the plate to the hole. I use the long screw in the opposite side of the plate to temporarily screw it in and bring the plate to the top, where it was supposed to be, then removed the scratch awl, and put in one of the original screws and tightened it. Then I was able to remove the long screw and put the other original screw in the other side. After that was done I tightened both of the original screws and and rest took about 15 minutes. Maybe this will help someone else in doing this bearing replacement?
This repair was on a Bosch Model 4100 table saw, which by the way is a GREAT saw!
Rick
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
