Screw,&#8203;&#8203; 3/&#8203;&#8203;8-16,&#8203;&#8203; 2.&#8203;&#8203;00,&#8203;&#8203; Gr5

Belt - 954-05040

Bowtie Cotter Pin - 714-04040

V Belt, 5L 70.90 - 954-04249A

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Adjustable Wrench, WD-40,prybar

Pulley fell off on mower deck

1 removed mower deck.
2 replaced missing pulley and check condition of all other pulleys.
3 reinstalled mower deck

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Fl-Wash. 3/8N I.D. - 736-0262

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set, Wrench Set

Idler pulley came off while I was mowing; after inspecting it I found the bearings had gone out. So I went to ereplacementparts.com and found all the components I would need to replace it.

1. I placed the mower on a ramp so I could easily get underneath it to work.
2. Dropped the mower deck all the way down to it's lowest position.
3. Installed the new pulley with Hex bolt, flat washers and Hex Flange nut. This only required the use of a 9/16 combination wrench and a 9/16 ratchet wrench.
4. Replaced the belt and the mower was back in operation.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

7-Speed Control Assembly - 983-04216

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, Wrench Set

Pully froze up and sheared the bolt.

Remove the main belt.
Drop the deck.
Slide it out from beneath the mower.
Replace the bolt, washer, thru the shaft and tighten the nut.
Reinstall the deck and belt and hop on.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set

Idle pulley on the cutting deck worn out and needed replacing

1. removed the cutting deck from the tractor
2. lifted the deck on one side and took off the idle pulleys
3. Replace the new idle pulleys
4. put back the cutting deck on the tractor
5. tested the cutting blades for noise and any ruff sound

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Fl-Wash. 3/8N I.D. - 736-0262

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, Wrench Set, Adjustable Wrench

Pulley bolt broke losing pulley, washer, pulley and broken belt

Pretty straight forward. Clean deck and install bolt,washer, pulley, and nut. Install new belt

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set, Adjustable Wrench

Guide pulley on mower deck was bent due to bolt failure

Removed old bolt and replaced with new

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Pin, Cotter .08 X 1.56 Intern. Rh - 714-04043

Riding Mower 42-inch Deck V-Belt - 954-04060C

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Pliers, Socket set, Wrench Set, Adjustable Wrench

Puller,idler broke,caused the Belt to come off.

Took off broken parts, and put on new parts. It was easy to medium putting the parts on. Once it was done I attached the mower deck back on the tractor and started cutting grass again.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used: