Easy
Less than 15 minutes
This is a genuine Delta replacement part that has been sourced from the original manufacturer to be used with table saws. The metal riving knife is a safety item that is used to separate material after the cut to prevent kickback. This item is sold as an individual replacement part.
Riving Knife DPEC002908
OEM part for: Delta
Part Number: DPEC002908
$62.28
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Compatibility
This part will fit the following 5 machines
Delta
36-725 10" Contractor Saw View Diagrams & Manuals
36-5000 10" Left Tilt Contractor Saw View Diagrams & Manuals
36-5052 10" Left Tilt Contractor Saw View Diagrams & Manuals
36-5100 10" Left Tilt Contractor Saw View Diagrams & Manuals
36-5152 10" Left Tilt Contractor Saw View Diagrams & Manuals
This item works with the following types of products:
- Saw Parts
This part replaces obsolete part #: DPEC002907
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Worked as expected
Quick delivery
Guest -
October 6, 2022
Verified Purchase
Very good response
This product arrived only a few days after ordering. I installed it and it is working perfectly.
Guest -
January 4, 2022
Verified Purchase
Finally the Correct One
Have purchased and returned 3 others .. finally got the correct one .. Thanks
Richard -
January 14, 2021
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Riving Knife
I can not make out the thickness specs engraved on the Riving Knife. Can you provide the minimum/maximum blade thickness specified for this Riving Knife?
JEFFREY
for model number Riving Knife DPEC002908
asked on 2024-01-12
Hi Jeffrey,
Thank you for your question. This is a 0.087 inch (2.2 mm) thick riving knife. Only use for a 10 inch (254 mm) blade with 0.10 (2.6 mm) minimum kerf width and 0.073 (1.85 mm) maximum body thickness. We hope this helps!
eReplacementParts Team January 12, 2024
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Bought used table saw that had the riving knife missing
Jaime - October 24, 2016
👍 2 of 2 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Adjustable Wrench
Parts Used
Actually I just pushed down on the riving knife and it snapped in to place.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Missing riving knife
Nicholas - December 5, 2018
👍 1 of 1 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, No tools
Parts Used
Installed new riving knife according to my table saw specs
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Riving Knife was missing
Jeffrey - January 9, 2022
Tool Type
Table Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, Allen Wrench
Parts Used
Installed replacement riving knife and adjusted it so it lined up with the blade.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bought used saw and riving knife assembly was missing
Todd - September 23, 2019
Tool Type
Table Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
, 1/4\\
Parts Used
1. UNPLUG saw
2. remove throat plate
3. remove blade
4. install assembly with 2 allen screws but leave slightly loose
5. install riving knife
6. put blade on with finger tightened nut/washer
7. align assembly to the blade
8. tighten assembly fully
9. tighten blade fully
10. put throat plate back on
11. plug her in and let her rip (pun intended)
2. remove throat plate
3. remove blade
4. install assembly with 2 allen screws but leave slightly loose
5. install riving knife
6. put blade on with finger tightened nut/washer
7. align assembly to the blade
8. tighten assembly fully
9. tighten blade fully
10. put throat plate back on
11. plug her in and let her rip (pun intended)
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
