Medium
15-30 minutes
Ring MS-622041
OEM part for: Krups
Part Number: MS-622041
$3.99
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Compatibility
This part will fit the following 8 machines
Krups
KM405550/5CA Coffee Maker Dahlstrom Timer View Diagrams & Manuals
KM405550/5CB Coffee Maker Dahlstrom Timer View Diagrams & Manuals
KM406550/5C0 Coffee Maker Dahlstrom 12 Inox Timer View Diagrams & Manuals
KM406555/5C0 Coffee Maker Dahlstrom 12 Inox Timer View Diagrams & Manuals
KM406555/5CA Coffee Maker Dahlstrom 12 Inox Timer View Diagrams & Manuals
KM406555/5CB Coffee Maker Dahlstrom 12 Inox Timer View Diagrams & Manuals
KM611850 Dahlstrom Timer Coffee Maker View Diagrams & Manuals
KM611D50 Dahlstrom 12 Inox Timer Coffee Maker View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Coffee Maker Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Ring
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
The heating plate dropped down because the plastic ring holding it up disintegrated
Theodore - October 18, 2019
Tool Type
Coffee Maker
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Pliers
1) Remove screws holding the base to the coffeemaker.
2) Remove base.
3) Remove the two screws holding the bracket that secures the heating element to the heating plate.
4) Remove the bracket.
5) Lift up heating element to gain access to the plate.
6) Remove plate.
7) Remove old disintegrating plastic "ring" and "seal" - a large silicone (?) washer that fits between the "ring" and the heating "plate."
8) Installed new ring. It was a snug fit, ensure it get fully seated before going further.
9) Install old seal.
10) Install old plate.
11) Set heating element back in place.
12) Install old bracket and screws, being mindful to not pinch any electrical wires.
13) While bottom cover is off, remove any old feet that are still attached.
14) Install new feet by pulling them through holes with pliers while pushing with thumb.
15) Fit bottom cover and install screws.
16) Test the coffeemaker.
2) Remove base.
3) Remove the two screws holding the bracket that secures the heating element to the heating plate.
4) Remove the bracket.
5) Lift up heating element to gain access to the plate.
6) Remove plate.
7) Remove old disintegrating plastic "ring" and "seal" - a large silicone (?) washer that fits between the "ring" and the heating "plate."
8) Installed new ring. It was a snug fit, ensure it get fully seated before going further.
9) Install old seal.
10) Install old plate.
11) Set heating element back in place.
12) Install old bracket and screws, being mindful to not pinch any electrical wires.
13) While bottom cover is off, remove any old feet that are still attached.
14) Install new feet by pulling them through holes with pliers while pushing with thumb.
15) Fit bottom cover and install screws.
16) Test the coffeemaker.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Plate rusted, ring crumbled, feet worn out
Howard - April 6, 2018
Tool Type
Coffee Maker
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Removed bottom cover
Detached plate holding bracket
Removed plate, ring, and seal and replaced, Ring was very difficult to get in place
Reattached holding bracket
Pulled feet from bottom cover with needle nose pliers and replaced. Feet difficult to insert,
Replaced bottom cover
Detached plate holding bracket
Removed plate, ring, and seal and replaced, Ring was very difficult to get in place
Reattached holding bracket
Pulled feet from bottom cover with needle nose pliers and replaced. Feet difficult to insert,
Replaced bottom cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
