Repair Center
Preferred Partners of
Repair Center  How to Install an Overhaul Kit in a Porter Cable Nail Gun

Why Read This Article?

Finish Nailer Repair - Replacing the Driver Guide (Ridgid Part # 79004001022)

Article Breakdown

Finish Nailer Repair - Replacing the Driver Guide (Ridgid Part # 79004001022)


Tools & Materials

  • Allen wrenches
  • Open-ended wrenches
  • Rubber mallet or hammer
  • Small punch
  • Pick

How to Install an Overhaul Kit in a Porter Cable Nail Gun

Finish Nailer Repair - Replacing the Driver Guide (Ridgid Part # 79004001022)
Nail guns require more frequent maintenance than other power tools. This is because the internal components experience rapid movement, lots of pressure and high forces. These forces can wear down the o-rings in the gun, causing them to leak air. You will need to install an overhaul kit in your nail gun if it is leaking from the nose, head or trigger.

If your nail gun is not leaking air, but has a broken driver, you will want to install a driver maintenance kit rather than an overhaul kit.
For this repair, we used a Porter Cable nail gun. Overhauls in other brands of nail guns will follow similar steps.
Before beginning this repair, be sure you find the right overhaul kit for your nail gun by using our Porter Cable parts search feature.
  Breaking Down the Gun

Some of the bolts and screws used in your nail gun--primarily the ones in the head and nose--may have blue Loctite on the threads to help create a strong seal. This may make them difficult to remove and is normal.

1. Remove the nail gun head

Remove the four fasteners that secure the head of the nail gun.


2. Remove the magazine

Remove the two fasteners and bolt that hold the magazine on the nail gun.


3. Remove the nose piece

Remove the four fasteners that secure the nose piece.


4. Remove the cylinder assembly

Use a rubber mallet or hammer to tap the nail gun housing. This should shake the cylinder loose so you can remove it.


Do not hit the cylinder assembly with the hammer as you could damage it.


Now you can remove the cylinder assembly from the gun.


Remove the cylinder alignment ring from the inside of the gun.


5. Remove the piston and bumper

Remove the piston and bumper from the cylinder assembly.

[Back to Top]   Overhauling the Piston, Head and Nose

It helps to lay out all the o-rings from the kit before you begin replacing them. This way you will be able to match the old o-rings with the new ones, streamlining the overhaul process.

1. Replace the cylinder o-rings

Replace each of the o-rings on the cylinder.


Add a thin layer of grease to the new o-rings.


Replace the check valve. Be sure that the shoulder on the check valve, the little ridge, is aligned towards the top of the cylinder. The check valve does not need grease.


2. Replace the piston o-ring

Replace and grease the piston o-ring.


3. Replace the alignment ring o-ring

Replace and grease the alignment ring o-ring.


4. Replace the head valve o-rings

Remove the cage from the head assembly.


Now remove the head valve. You will see two o-rings on the outside of the valve assembly. Another one is hidden just inside the valve with a piece of plastic and a spring in the way. Hold the assembly securely, then push the plastic piece to the side to get access to the inner o-ring.


Replace the three o-rings and apply grease to each of them.



5. Reassemble the head valve

Reassemble the head valve into the head of the gun.


6. Replace the nose o-ring

Replace the o-ring in the nose of the gun. This o-ring does not need grease.


Fasten the nose to the gun, torquing each screw a little bit at a time to guarantee a good seal.


7. Reinstall the head valve and cylinder assembly

Slide the new bumper onto the piston (with the arrow pointing up).

Slide the piston assembly into the cylinder and seat the bumper.


Slide the alignment ring over the cylinder.


If you extend the piston out of the cylinder, you will find it easier to align the driver with the nose. Align the nose and driver and slide the cylinder assembly into place.




Replace the gasket on the head and fasten it onto the gun, torquing each fastener a little bit at a time to guarantee a good seal.

[Back to Top]   Overhauling the Trigger

Porter Cable uses two types of triggers in their nail guns: triggers that thread into place and triggers help in place by pins. If your nail gun uses pin triggers, you can simply replace your trigger valve with the one in the overhaul kit. If your gun uses a threaded trigger, you will have to rebuild it using parts from the new trigger valve assembly.

1. Remove the trigger assembly

Remove the o-ring that holds the trigger pin into the gun and remove the trigger pin.



Now you can remove the trigger away from the gun.


Use a wrench to remove the trigger valve from the gun.


2. Break down the trigger valves

Pull on the two sides of your original valve to gain access to its internal components. Use a small punch to remove the pins that hold the new valve together.


3. Rebuild the trigger valve

Now you can swap parts between the two valves. Use the new valve's spring, brass fitting, inner valve and o-rings on your new valve.


Assemble your old, threaded valve with the new parts and add a thin layer of grease to the o-rings.


3. Reinstall the trigger assembly and magazine

Thread the trigger assembly back into your nail gun and tighten the valve down.


Reinstall the trigger, trigger pin and the o-ring that holds the pin in place.


Finalize the repair by reinstalling the magazine onto your gun.

[Back to Top]   Conclusion
Installing an overhaul kit is a simple, if somewhat long, repair that you can easily do yourself. This repair will definitely save you money compared to the repair shop option, and if you use your nail gun for a lot of projects, you will find that you have to overhaul it frequently.
Armed with the knowledge in this article, you can fix any leak issues with your nail gun in about an hour, which means you can get back to work on those important projects sooner.
Before you begin any repair, make sure you have the right parts by using our handy power tool parts search feature.   [Back to Top] What We're About

Fixing things makes sense...

...And we make it easy! With our Fix app, you always have a personalized repair guide on-hand. Easily find manuals and replacement parts on your phone while you’re DIYing in the garage or garden.

"Love the flexibility of the app to add everything in the home and garage. Access to manuals and parts right there makes it convenient."

Available on the App Store Get it on Google Play
7036 South High Tech Dr.
Midvale, UT 84047
visa mastercard discover american express PayPal