Easy
15-30 minutes
This power cord is a genuine Skil/Bosch replacement part, not generic. Just like the original cord on your tool, this cord is built tough. Thick insulation ensures long service life and safe electrical isolation. This is a three wire cord (includes ground plug) and connection terminals are already installed. This cord also includes a metal locking tab for a secure attachment to your tool.
This cord is compatible with the tools listed below. Because of oversize cord thickness and three wires, this cord is not guaranteed to fit any other power tools.
Power Cord 4810003233
OEM part for: Skil, Bosch
Part Number: 4810003233
$19.62
In Stock
Ships within 1 business day 
Jump To:
Product Description ?
- O.E.M. Skil/Bosch replacement power cord
- Three wires (includes ground wire)
- 8 Feet. 14 gauge, 3 wire.
- Classification: Part
- Weight: 0.87 lbs.
- Also Known As: AC Cord, Power Supply Cord, Cord Set, Electric Cord
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This part will fit the following 38 machines
Skil
5825 TYPE 2 (F01258250A) 6-1/2 in. Worm Drive Saw View Diagrams & Manuals
HD77 Type 17 Worm Drive Saw (Skilsaw 77) View Diagrams & Manuals
5860 (F012586099) Circular Saw View Diagrams & Manuals
HD77M (F012HM7702) 7 1/4" Magnesium Worm Drive Skilsaw View Diagrams & Manuals
SHD77 (F012SD7700) 7 1/4" Worm Drive Skilsaw View Diagrams & Manuals
SHD77 (F012SD7705) 7 1/4" Worm Drive Skilsaw View Diagrams & Manuals
SHD77M (F012SD7702) 7 1/4" Magnesium Worm Drive Skilsaw View Diagrams & Manuals
SHD77M (F012SD7707) 7 1/4" Magnesium Worm Drive Skilsaw View Diagrams & Manuals
HD5860 (F01258600A) Worm Drive Skilsaw View Diagrams & Manuals
5865 Power Saw View Diagrams & Manuals
MAG77LT (F012XD7700) Worm Drive Skilsaw View Diagrams & Manuals
HD77 (F012HD77LA) Circular Hand Saw View Diagrams & Manuals
SHD77M (F012SD7712) Circular Hand Saw View Diagrams & Manuals
HD77M (F012HM7700) Circular Hand Saw View Diagrams & Manuals
MAG77-75 7-1/4" Skilsaw View Diagrams & Manuals
HD 5825 (F01258250A) Circular Hand Saw View Diagrams & Manuals
SPT70WM (F012701000) Circular Hand Saw View Diagrams & Manuals
SPT77W (F012771000) Circular Saw View Diagrams & Manuals
SPT77WM (F012771100) Circular Saw View Diagrams & Manuals
SPT77WML (F012771200) Circular Saw View Diagrams & Manuals
77 (F012007799) Circular Hand Saw View Diagrams & Manuals
SPT70WM-01 Saw 10-1/4 In. Magnesium Sawsquatch Worm Drive Saw; Saw Blade View Diagrams & Manuals
SPT77W-01 Saw 7-1/4 In. Worm Drive Saw; Sawblade View Diagrams & Manuals
SPT77W-22 Saw 7-1/4 In. Worm Drive Saw View Diagrams & Manuals
SPT77WM-22 Saw 7-1/4 In. Magnesium Worm Drive Saw View Diagrams & Manuals
SPT77WML-01 Saw 7-1/4 In. Lightweight Worm Drive Saw View Diagrams & Manuals
SPT77WML-22 Saw 7-1/4 In. Lightweight Magnesium Worm Drive Saw View Diagrams & Manuals
SPT70WM-22 Circular Saw View Diagrams & Manuals
Bosch
1677M (0601677039) 7-1/4" Worm Drive Saw View Diagrams & Manuals
1678A (0601678039) 7-1/4" Worm Drive Saw View Diagrams & Manuals
1677C-100 (0601677168) Circular Saw View Diagrams & Manuals
1677DC-100 (0601677190) Circular Saw View Diagrams & Manuals
1678 (0601678039) Un-Hd Port. Circular Saw View Diagrams & Manuals
CSW41 (3601F6D010) Circular Saw View Diagrams & Manuals
CSW41 (3601F6D011) Circular Hand Saw View Diagrams & Manuals
HD77 (F012HD7720) Circular Saw View Diagrams & Manuals
SHD77 (F012SD7720) Circular Saw View Diagrams & Manuals
MAG77 (F012SD7722) Circular Saw View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Saw Parts
- Circular Saw Parts
This part replaces obsolete part #: 1619X08527, 1619X01570, 2610914296, 2610991862
Repair Videos ?
Watch the Repair Video for
Power Cord
Articles:
|
This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
September 18, 2009
|
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
21
4 stars
2
3 stars
1
2 stars
0
1 stars
0
< PREV
- 1
- 2
- 3
No problems!
Perfect replacement cord for my skilsaw 77 it cam with pre attached wire lugs on the cord that were perfect lengths and it went back together nicely.
Guest -
October 21, 2023
Verified Purchase
Best place to buy replacement parts!
This was the right part, saws are going again. Best place to buy replacement parts!
Rick -
September 22, 2023
Verified Purchase
Fit like it should; good quality.
This power cord was purchased to replace a damaged power cord. It fit like the factory cord: same gauge, wire ends were terminated, length was good. Good quality part.
Guest -
August 3, 2022
Verified Purchase
It works good
Top quality and was what I ordered ...
Guest -
December 22, 2021
Verified Purchase
Thanks
Good
Guest -
June 29, 2021
Verified Purchase
all good
all good
Ed -
December 5, 2020
Verified Purchase
Just what I ordered from my little mini welder work perfect
Just what I ordered from my little mini welder work perfect
Guest -
November 30, 2020
Verified Purchase
Fast delivery, saved some $$
Works great, easy install.
Guest -
September 8, 2020
Verified Purchase
Perfect works great
It arrived as it said it would no damage on it or the package thank you
Guest -
August 10, 2020
Verified Purchase
Easy Repair. Worked like it should.
Arrived within the time it was supposed to. Fit fine, good quality. I now have a working Skill saw.
Guest -
August 8, 2020
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Power Cord
Will this work for skilsaw SPT67WE
Bill
for model number SPT67WE
asked on 2022-02-15
Hello Bill, Thank you for your inquiry. We have researched the model number you have provided and do not show this part as compatible. We show the compatible power cord as part# 4810218001. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
eReplacementParts Team February 15, 2022
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Power Cord Cut
edwin - July 22, 2016
👍 6 of 7 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Remove handle side plate.
2. Remove 3 Screws connecting cord.
3. Remove 2 Screws securing trigger.
4. Removed old cord and installed new cord by replacing the items above.
2. Remove 3 Screws connecting cord.
3. Remove 2 Screws securing trigger.
4. Removed old cord and installed new cord by replacing the items above.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Needed a new cord
William - August 25, 2017
👍 2 of 2 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Wrench Set
Parts Used
Remove one handle half, Remove the cord wires from the switch and the ground wire
Remove the cord clamp. Slide the old cord relief from off of the old cord and slide it on the new cord. Connect the wires from new cord to the switch and the ground wire. Install the cord clamp. Install the handle half.
Remove the cord clamp. Slide the old cord relief from off of the old cord and slide it on the new cord. Connect the wires from new cord to the switch and the ground wire. Install the cord clamp. Install the handle half.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bad cord on a skilsaw
James - June 8, 2018
👍 2 of 3 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
Removed handle and replace cord and cord guard
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Armature commutator damaged by abrasive grit, have also done the replacement when the cooling fan shears off the armature
Thoms - September 8, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Hard
Time
1-2 hours
Tools Used
Screwdriver, Socket set, Wrench Set, Nutdriver, Adjustable Wrench, Bearing driver, armature jig (homemade), small impact driver
1. Drain oil from gearbox
2. Remove brushes
3. Remove guide plate
4. Remove large plastic plug from rear of saw
5. Remove nut behind plastic plug with impact driver while holding down while holding down saw blade stop..
6. Remove saw guide plate and front housing.
6. Press or drive armature out of gearbox brearing.
7. Install new bearing on commutator side of new armature using a simple jig to hold the armature.
8. Slide new armature into the gearbox housing.
9. Reinstall nut and carefully tighten with impact driver. This will pull the armature through the gearbox until it stops when the armature shoulder contacts the inner bearing race on the armature side of the gearbox. Take your time with this.
10. Reassemble saw.
11. Refill gearbox with oil.
12. Replace brushes.
Note: I've done this type of replacement a number of times on Skil circular saws without replacing the bearings on the gearbox side and not had any long term problems. But it is likely that Skil recommends replacing the two gearbox bearings as part of the procedure.
2. Remove brushes
3. Remove guide plate
4. Remove large plastic plug from rear of saw
5. Remove nut behind plastic plug with impact driver while holding down while holding down saw blade stop..
6. Remove saw guide plate and front housing.
6. Press or drive armature out of gearbox brearing.
7. Install new bearing on commutator side of new armature using a simple jig to hold the armature.
8. Slide new armature into the gearbox housing.
9. Reinstall nut and carefully tighten with impact driver. This will pull the armature through the gearbox until it stops when the armature shoulder contacts the inner bearing race on the armature side of the gearbox. Take your time with this.
10. Reassemble saw.
11. Refill gearbox with oil.
12. Replace brushes.
Note: I've done this type of replacement a number of times on Skil circular saws without replacing the bearings on the gearbox side and not had any long term problems. But it is likely that Skil recommends replacing the two gearbox bearings as part of the procedure.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
30-year old Skilsaw needed a little maintenance. ereplacementparts were perfect.
John - February 16, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Remove the screws from the handle assembly, then unscrew switch from handle and remove the cord clamp. Remove the cord leads from the switch and the ground wire. Discard old cord. Slide the new cord relief onto the new cord. Install the cord leads on the switch , then the ground lead. Attach switch to handle , then put the cord clamp back on. Press the handle together. Make sure there are no wires being pinched, then install the handle on to the saw. To replace the brushes. Remove the brush caps with a screwdriver, then remove the old brushes. Install the new brushes, then screw the brush caps back on. Check oil level in the saw and add more if needed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Electric cord was old/cracked and the on/off switch would not shut off any longer
Gary - August 11, 2018
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
1. Removed handle, 4 screws
2. Removed switch, 1 screw
3 Installed new switch
4. Removed 3 screws to remove cord
5. Installed new cord
6. Reassembled handle
2. Removed switch, 1 screw
3 Installed new switch
4. Removed 3 screws to remove cord
5. Installed new cord
6. Reassembled handle
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Cord was broke ,brushes were old, lever was broke
Thomas - July 26, 2018
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Star bits
Dismantled handle, removed damaged cord, replaced with new... removed old brushes, replaced with new...removed broken lever, replaced with new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Saw was dropped and fractured handles
Gary - July 10, 2018
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Socket set, Torks bit set and 1/4\\
Removed handle half on main grip, took picture for reference with phone to reference wiring on the switch, detached ground to motor case, removed switch and old cord and guard, transferred switch and attached new cord and guard to new grip half, removed old grip half and installed new grip half assembly and attached ground other new grip half and new top handle.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
A lot of sparking in the motor; short cord.
Greg - April 23, 2018
Tool Type
Circular Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver
Removed covers for brushes then replaced old brushes with new ones. Removed screws from handle assembly then removed screws holding terminals on old power cord. Replaced old cord with new one and replaced the screws. My vintage Skilsaw 825 worm drive is ready for another 50 years of use!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Saw slipped and hit the concrete floor. The handle was shattered. Oops!
Mike - April 24, 2018
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
1. With a screwdriver, took apart the broken handle.
2. Disconnected the power cord leads.
3. Connected the new power cord.
4. Reassembled the new handle.
5. Pluged in the cord to the outlet and she works just fine. Thanks!
2. Disconnected the power cord leads.
3. Connected the new power cord.
4. Reassembled the new handle.
5. Pluged in the cord to the outlet and she works just fine. Thanks!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Load More Install Stories
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
