Power Cord 4810003233
Part Number: 4810003233
Order within the next 1 hour
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: 1619X08527, 1619X01570, 2610914296 and 2610991862.
Product Information
Specifications
|
Description:
This power cord is a genuine Skil/Bosch replacement part, not generic. Just like the original cord on your tool, this cord is built tough. Thick insulation ensures long service life and safe electrical isolation. This is a three wire cord (includes ground plug) and connection terminals are already installed. This cord also includes a metal locking tab for a secure attachment to your tool. This cord is compatible with the tools listed below. Because of oversize cord thickness and three wires, this cord is not guaranteed to fit any other power tools. |
Frequently Purchased With
Compatibility
the 44 compatible machines
This part is compatible with the following machines:
Skil
5825 TYPE 2 (F01258250A) 6-1/2 in. Worm Drive Saw
HD77 Type 17 Worm Drive Saw (Skilsaw 77)
5860 (F012586099) Circular Saw
5860 (F012586099) Circular Saw
HD77M (F012HM7702) 7 1/4" Magnesium Worm Drive Skilsaw
SHD77 (F012SD7700) 7 1/4" Worm Drive Skilsaw
SHD77 (F012SD7705) 7 1/4" Worm Drive Skilsaw
SHD77M (F012SD7702) 7 1/4" Magnesium Worm Drive Skilsaw
SHD77M (F012SD7707) 7 1/4" Magnesium Worm Drive Skilsaw
HD5860 (F01258600A) Worm Drive Skilsaw
5865 Power Saw
MAG77LT (F012XD7700) Worm Drive Skilsaw
HD77 (F012HD77LA) Circular Hand Saw
HD77 (F012HD77LA) Circular Hand Saw
SHD77M (F012SD7712) Circular Hand Saw
SHD77M (F012SD7712) Circular Hand Saw
HD77 Type 17 Worm Drive Saw (Skilsaw 77)
5860 (F012586099) Circular Saw
5860 (F012586099) Circular Saw
HD77M (F012HM7702) 7 1/4" Magnesium Worm Drive Skilsaw
SHD77 (F012SD7700) 7 1/4" Worm Drive Skilsaw
SHD77 (F012SD7705) 7 1/4" Worm Drive Skilsaw
SHD77M (F012SD7702) 7 1/4" Magnesium Worm Drive Skilsaw
SHD77M (F012SD7707) 7 1/4" Magnesium Worm Drive Skilsaw
HD5860 (F01258600A) Worm Drive Skilsaw
5865 Power Saw
MAG77LT (F012XD7700) Worm Drive Skilsaw
HD77 (F012HD77LA) Circular Hand Saw
HD77 (F012HD77LA) Circular Hand Saw
SHD77M (F012SD7712) Circular Hand Saw
SHD77M (F012SD7712) Circular Hand Saw
HD77M (F012HM7700) Circular Hand Saw
HD77M (F012HM7700) Circular Hand Saw
MAG77-75 7-1/4" Skilsaw
HD 5825 (F01258250A) Circular Hand Saw
SPT70WM (F012701000) Circular Hand Saw
SPT77W (F012771000) Circular Saw
SPT77WM (F012771100) Circular Saw
SPT77WML (F012771200) Circular Saw
77 (F012007799) Circular Hand Saw
SPT70WM-01 Saw 10-1/4 In. Magnesium Sawsquatch Worm Drive Saw; Saw Blade
SPT77W-01 Saw 7-1/4 In. Worm Drive Saw; Sawblade
SPT77W-22 Saw 7-1/4 In. Worm Drive Saw
SPT77WM-22 Saw 7-1/4 In. Magnesium Worm Drive Saw
SPT77WML-01 Saw 7-1/4 In. Lightweight Worm Drive Saw
SPT77WML-22 Saw 7-1/4 In. Lightweight Magnesium Worm Drive Saw
SPT70WM-22 Circular Saw
HD77M (F012HM7700) Circular Hand Saw
MAG77-75 7-1/4" Skilsaw
HD 5825 (F01258250A) Circular Hand Saw
SPT70WM (F012701000) Circular Hand Saw
SPT77W (F012771000) Circular Saw
SPT77WM (F012771100) Circular Saw
SPT77WML (F012771200) Circular Saw
77 (F012007799) Circular Hand Saw
SPT70WM-01 Saw 10-1/4 In. Magnesium Sawsquatch Worm Drive Saw; Saw Blade
SPT77W-01 Saw 7-1/4 In. Worm Drive Saw; Sawblade
SPT77W-22 Saw 7-1/4 In. Worm Drive Saw
SPT77WM-22 Saw 7-1/4 In. Magnesium Worm Drive Saw
SPT77WML-01 Saw 7-1/4 In. Lightweight Worm Drive Saw
SPT77WML-22 Saw 7-1/4 In. Lightweight Magnesium Worm Drive Saw
SPT70WM-22 Circular Saw
Bosch
Products Compatibility
This item works with the following types of products:
- • Circular Saw
- • Saw
Repair Guides
Articles:
This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
September 18, 2009
|
Questions & Answers for Power Cord
Will this work for skilsaw SPT67WE
Bill
for model number SPT67WE
asked on 2022-02-15
Hello Bill, Thank you for your inquiry. We have researched the model number you have provided and do not show this part as compatible. We show the compatible power cord as part# 4810218001. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
eReplacementParts Team February 15, 2022
Repair Instructions: Submitted by Customers Like You
6 of 7 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Power Cord Cut
1. Remove handle side plate.
2. Remove 3 Screws connecting cord.
3. Remove 2 Screws securing trigger.
4. Removed old cord and installed new cord by replacing the items above.
2. Remove 3 Screws connecting cord.
3. Remove 2 Screws securing trigger.
4. Removed old cord and installed new cord by replacing the items above.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set
Needed a new cord
Remove one handle half, Remove the cord wires from the switch and the ground wire
Remove the cord clamp. Slide the old cord relief from off of the old cord and slide it on the new cord. Connect the wires from new cord to the switch and the ground wire. Install the cord clamp. Install the handle half.
Remove the cord clamp. Slide the old cord relief from off of the old cord and slide it on the new cord. Connect the wires from new cord to the switch and the ground wire. Install the cord clamp. Install the handle half.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 3 people found this instruction helpful
Tool Type:
Circular Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Bad cord on a skilsaw
Removed handle and replace cord and cord guard
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Hard
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Socket set, Wrench Set, Nutdriver, Adjustable Wrench, Bearing driver, armature jig (homemade), small impact driver
Armature commutator damaged by abrasive grit, have also done the replacement when the cooling fan shears off the armature
1. Drain oil from gearbox
2. Remove brushes
3. Remove guide plate
4. Remove large plastic plug from rear of saw
5. Remove nut behind plastic plug with impact driver while holding down while holding down saw blade stop..
6. Remove saw guide plate and front housing.
6. Press or drive armature out of gearbox brearing.
7. Install new bearing on commutator side of new armature using a simple jig to hold the armature.
8. Slide new armature into the gearbox housing.
9. Reinstall nut and carefully tighten with impact driver. This will pull the armature through the gearbox until it stops when the armature shoulder contacts the inner bearing race on the armature side of the gearbox. Take your time with this.
10. Reassemble saw.
11. Refill gearbox with oil.
12. Replace brushes.
Note: I've done this type of replacement a number of times on Skil circular saws without replacing the bearings on the gearbox side and not had any long term problems. But it is likely that Skil recommends replacing the two gearbox bearings as part of the procedure.
2. Remove brushes
3. Remove guide plate
4. Remove large plastic plug from rear of saw
5. Remove nut behind plastic plug with impact driver while holding down while holding down saw blade stop..
6. Remove saw guide plate and front housing.
6. Press or drive armature out of gearbox brearing.
7. Install new bearing on commutator side of new armature using a simple jig to hold the armature.
8. Slide new armature into the gearbox housing.
9. Reinstall nut and carefully tighten with impact driver. This will pull the armature through the gearbox until it stops when the armature shoulder contacts the inner bearing race on the armature side of the gearbox. Take your time with this.
10. Reassemble saw.
11. Refill gearbox with oil.
12. Replace brushes.
Note: I've done this type of replacement a number of times on Skil circular saws without replacing the bearings on the gearbox side and not had any long term problems. But it is likely that Skil recommends replacing the two gearbox bearings as part of the procedure.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
30-year old Skilsaw needed a little maintenance. ereplacementparts were perfect.
Remove the screws from the handle assembly, then unscrew switch from handle and remove the cord clamp. Remove the cord leads from the switch and the ground wire. Discard old cord. Slide the new cord relief onto the new cord. Install the cord leads on the switch , then the ground lead. Attach switch to handle , then put the cord clamp back on. Press the handle together. Make sure there are no wires being pinched, then install the handle on to the saw. To replace the brushes. Remove the brush caps with a screwdriver, then remove the old brushes. Install the new brushes, then screw the brush caps back on. Check oil level in the saw and add more if needed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Electric cord was old/cracked and the on/off switch would not shut off any longer
1. Removed handle, 4 screws
2. Removed switch, 1 screw
3 Installed new switch
4. Removed 3 screws to remove cord
5. Installed new cord
6. Reassembled handle
2. Removed switch, 1 screw
3 Installed new switch
4. Removed 3 screws to remove cord
5. Installed new cord
6. Reassembled handle
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Star bits
Cord was broke ,brushes were old, lever was broke
Dismantled handle, removed damaged cord, replaced with new... removed old brushes, replaced with new...removed broken lever, replaced with new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Socket set, Torks bit set and 1/4\\
Saw was dropped and fractured handles
Removed handle half on main grip, took picture for reference with phone to reference wiring on the switch, detached ground to motor case, removed switch and old cord and guard, transferred switch and attached new cord and guard to new grip half, removed old grip half and installed new grip half assembly and attached ground other new grip half and new top handle.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
A lot of sparking in the motor; short cord.
Removed covers for brushes then replaced old brushes with new ones. Removed screws from handle assembly then removed screws holding terminals on old power cord. Replaced old cord with new one and replaced the screws. My vintage Skilsaw 825 worm drive is ready for another 50 years of use!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Saw slipped and hit the concrete floor. The handle was shattered. Oops!
1. With a screwdriver, took apart the broken handle.
2. Disconnected the power cord leads.
3. Connected the new power cord.
4. Reassembled the new handle.
5. Pluged in the cord to the outlet and she works just fine. Thanks!
2. Disconnected the power cord leads.
3. Connected the new power cord.
4. Reassembled the new handle.
5. Pluged in the cord to the outlet and she works just fine. Thanks!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
24 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
21
4 stars
2
3 stars
1
2 stars
0
1 stars
0
< PREV
- 1
- 2
- 3
No problems!
Perfect replacement cord for my skilsaw 77 it cam with pre attached wire lugs on the cord that were perfect lengths and it went back together nicely.
Guest -
October 21, 2023
Verified Purchase
Best place to buy replacement parts!
This was the right part, saws are going again. Best place to buy replacement parts!
Rick -
September 22, 2023
Verified Purchase
Fit like it should; good quality.
This power cord was purchased to replace a damaged power cord. It fit like the factory cord: same gauge, wire ends were terminated, length was good. Good quality part.
Guest -
August 3, 2022
Verified Purchase
It works good
Top quality and was what I ordered ...
Guest -
December 22, 2021
Verified Purchase
Thanks
Good
Guest -
June 29, 2021
Verified Purchase
all good
all good
Ed -
December 5, 2020
Verified Purchase
Just what I ordered from my little mini welder work perfect
Just what I ordered from my little mini welder work perfect
Guest -
November 30, 2020
Verified Purchase
Fast delivery, saved some $$
Works great, easy install.
Guest -
September 8, 2020
Verified Purchase
Perfect works great
It arrived as it said it would no damage on it or the package thank you
Guest -
August 10, 2020
Verified Purchase
Easy Repair. Worked like it should.
Arrived within the time it was supposed to. Fit fine, good quality. I now have a working Skill saw.
Guest -
August 8, 2020
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
- 2
- 3
Product Information
Repair Guides
Articles:
This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
September 18, 2009
|