eReplacementParts.com
877-346-4814
Makita Parts

Power Cord 664265-4

OEM part for: Makita

Part Number: 664265-4


Install
Videos!
Grid squares measure 1x1 inch
In Stock
Order within the next 9 hours and your part ships today!
Easy 15-30 minutes (53 rated repairs)?
OEM: Original Equipment Manufacturer ?
Makita
Does this d-block d-md-none fit my product?

Product Description ?

This is a genuine Makita replacement power tool cord. It is constructed with thick insulation for long service life and a strong two-prong plug. The connection end of the cord comes pre stripped for easy installation. The cord is eight feet long with sturdy 16 gauge wires.

This cord will fit the Makita tools listed below. It can work for other applications and for other tools as well, but compatibility is not guaranteed.

  • Length: 8'
  • Gauge: 16
  • Wires: 2
  • Type: Bare Wire
  • Genuine Makita replacement power tool cord
  • 2 Wire
  • Tough 16 gauge wiring
  • 8 feet in length
  • Sturdy plug and insulation
  • Classification: Part
  • Weight: 0.57 lbs.
  • Also Known As: AC Cord, Power Supply Cord, Cord Set, Electric Cord
  • Shipping: Ships Worldwide

Compatibility

This part will fit the following 96 machines

Makita

5007NB Circular Saw View Diagrams & Manuals
5740NB Circular Saw View Diagrams & Manuals
LS1011 Compound Miter Saw View Diagrams & Manuals
LS1020 Miter Saw View Diagrams & Manuals
LS1030 Miter Saw View Diagrams & Manuals
9015B Grinder View Diagrams & Manuals
9016B Grinder View Diagrams & Manuals
5008NB Circular Saw View Diagrams & Manuals
9015DB Angle Grinder View Diagrams & Manuals
9565CV Angle Grinder View Diagrams & Manuals
5007NBA Circular Saw View Diagrams & Manuals
9016DB Angle Grinder View Diagrams & Manuals
9563CV Grinder View Diagrams & Manuals
9564CV Angle Grinder View Diagrams & Manuals
9564CVL Angle Grinder View Diagrams & Manuals
6922NB Shear Wrench View Diagrams & Manuals
5007S Circular Saw View Diagrams & Manuals
5077B Hypoid Saw View Diagrams & Manuals
DA4031 Angle Drill View Diagrams & Manuals
9015A Angle Grinder View Diagrams & Manuals
9566CV Cut Off Angle Grinder View Diagrams & Manuals
JR3060T Reciprocating Saw View Diagrams & Manuals
TW1000 Impact Wrench View Diagrams & Manuals
LS1000 10 inch Miter Saw View Diagrams & Manuals
5007NBK Type 1 7-1/4" 15A Heavy-Gauge Aluminium Base Circular Saw View Diagrams & Manuals
GA6010Z 10.5A 6" Cutoff / Angle Grinder View Diagrams & Manuals
GA5020 10.5A 5" SJS Angle Grinder View Diagrams & Manuals
GA5010Z 10.5A 5" Angle Grinder View Diagrams & Manuals
9566PC 6" SJS Cutoff / Angle Grinder View Diagrams & Manuals
9565PC 5" SJS Angle Grinder View Diagrams & Manuals
9564PC 4-1/2" SJS Angle Grinder View Diagrams & Manuals
2401B 10" Miter Saw View Diagrams & Manuals
DA4030 1/2" Angle Drill View Diagrams & Manuals
LS1430 14" Miter Saw View Diagrams & Manuals
LS1400 14" Miter Saw View Diagrams & Manuals
SP6000K1 6-1/2" Plunge Circular Saw with 55" Guide Rail View Diagrams & Manuals
GA5020Y Super Joint Angle Grinder View Diagrams & Manuals
GA6020 6" Angle Grinder View Diagrams & Manuals
GA4542C 4-1/2" SJS II High-Power Angle Grinder View Diagrams & Manuals
4100NH2ZX1 (Type 1) Saw View Diagrams & Manuals
4100NH2ZX1 (Type 2) Saw View Diagrams & Manuals
4100NH2ZX1 (Type 3) Saw View Diagrams & Manuals
4100NH2ZX (Type 2) Saw View Diagrams & Manuals
4100NH2ZX (Type 3) Saw View Diagrams & Manuals
4100NSZX1 (Type 1) Saw View Diagrams & Manuals
4100NSZX1 (Type 2) Saw View Diagrams & Manuals
4100NSZX1 (Type 3) Saw View Diagrams & Manuals
4100NSZX (Type 1) Saw View Diagrams & Manuals
4100NSZX (Type 2) Saw View Diagrams & Manuals
4100NSZX (Type 3) Saw View Diagrams & Manuals
5007NBA-K Saw View Diagrams & Manuals
5008NBA (Type 2) Saw View Diagrams & Manuals
5008NBA (Type 3) Saw View Diagrams & Manuals
5008NB (Type 2) Saw View Diagrams & Manuals
5008NB (Type 3) Saw View Diagrams & Manuals
5008NB (Type 4) Saw View Diagrams & Manuals
9564P Grinder View Diagrams & Manuals
9566PCX1 Grinder View Diagrams & Manuals
GA4542C01 Grinder View Diagrams & Manuals
GA5010 Grinder View Diagrams & Manuals
GA5040 Grinder View Diagrams & Manuals
GA5040X1 Grinder View Diagrams & Manuals
GA5042C Grinder View Diagrams & Manuals
GA5042C01 Grinder View Diagrams & Manuals
GA5042CX1 Grinder View Diagrams & Manuals
GA6010 Grinder View Diagrams & Manuals
GA6010ZX2 Grinder View Diagrams & Manuals
GA6020YX1 Grinder View Diagrams & Manuals
HG1100 (Type 2) Misc View Diagrams & Manuals
HS7600 (Type 1) Saw View Diagrams & Manuals
HS7600 (Type 2) Saw View Diagrams & Manuals
JR3050T (Type 3) Saw View Diagrams & Manuals
JR3050TX (Type 2) Saw View Diagrams & Manuals
JR3050TX (Type 3) Saw View Diagrams & Manuals
JR3050TY (Type 2) Saw View Diagrams & Manuals
JR3050TY (Type 3) Saw View Diagrams & Manuals
SP6000 (Type 1) Saw View Diagrams & Manuals
SP6000 (Type 2) Saw View Diagrams & Manuals
SP6000 (Type 3) Saw View Diagrams & Manuals
SP6000 (Type 4) Saw View Diagrams & Manuals
SP6000X1 (Type 1) Saw View Diagrams & Manuals
SP6000X1 (Type 2) Saw View Diagrams & Manuals
SP6000X1 (Type 3) Saw View Diagrams & Manuals
SP6000X1 (Type 4) Saw View Diagrams & Manuals
SP6000X2 (Type 1) Saw View Diagrams & Manuals
SP6000X2 (Type 2) Saw View Diagrams & Manuals
SP6000X2 (Type 3) Saw View Diagrams & Manuals
SP6000X2 (Type 4) Saw View Diagrams & Manuals
Show More Compatible Models
Don't see yours? Try searching our site for :

This item works with the following types of products:

  • Circular Saw Parts
  • Saw Parts
  • Miter Saw Parts
  • Grinder Parts
  • Shear Parts
  • Drill Parts
  • Reciprocating Saw Parts
  • Impact Wrench Parts

This part replaces obsolete part #: 664234-5

Repair Videos ?

Watch the Repair Video for Power Cord
Articles:
This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
September 18, 2009
Step-by-step instructions for removing and installing the power cord on your Makita angle drill....
February 27, 2018

Customer Part Reviews ?

4.9
Average Rating (out of 5):
44 Reviews
Click to filter by ratings:
5 stars
41
4 stars
2
3 stars
1
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
  • 2
  • 3
NEXT >
  • Works as it should
    Came in a timely manner, does not come with ends on cord. Had too get some
    Guest - September 12, 2023 Verified Purchase
    Got the right parts.
    I have never gotten the wromg part from this website. They ars a great resource and reliable. Helps me run my business with ease.
    David - August 12, 2023 Verified Purchase
    Makita replacement parts
    Cord worked perfectly
    Guest - August 1, 2023 Verified Purchase
    Everything was exactly as promised, including timely delivery!
    All good!
    Guest - May 24, 2023 Verified Purchase
    Easy repair same as original part.
    Arrived quickly
    Guest - May 10, 2023 Verified Purchase
    Replacement power cord
    Fast delivery and good price. Should have it installed shortly.
    Guest - March 6, 2023 Verified Purchase
    Easy repair, correct part.
    Power saw is fixed, don't have to worry about being electrocuted.
    Gary - December 17, 2022 Verified Purchase
    Great Company
    My Makita circular saw cord was shot after 15 years of work. Replacement cord was in shock, easy to order, reasonable price and fast delivery allowed me to get it back in action. Thank you!
    Guest - November 19, 2022 Verified Purchase
    thanks
    all parts arrived at once - four power tools have new life!
    Guest - July 28, 2022 Verified Purchase
    Right part
    This is a very old Makita saw that I love. I was glad to find original cord to fix it
    Guest - April 16, 2022 Verified Purchase
    t
    t
    t - t days ago Verified Purchase
    eReplacementParts Team
    t

    Questions & Answers ?

    Our customer Service team is at the ready daily to answer your part and product questions.

    photo of team member
    Ask our Team

    We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    Does this fit my product?

    Questions & Answers for Power Cord


    will this cord fit a Makita circular saw 5007 NB
    Eddie for model number 5007nb asked on 2023-04-29
    Hello Eddie, Thank you for writing. The Power Cord for this model would be Power Cord Part Number: 664265-4. We hope this helps!
    eReplacementParts Team April 29, 2023

    Customer Repair Instructions ?

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

    Easy 15-30 minutes (53 rated repairs)?

    Someone had cut plug wire near saw end

    Larry - September 15, 2016
    👍 19 of 19 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver, stuff to put ends on wire

    1. Removed 4 or 5 Philips screws from handle (nuts stayed in removed handle piece)
    2. Removed 2 screws holding tension on cords end the one holding switch to saw
    3. Un-screwed wire from switch (black wire white wire) remember which wire goes where
    (white wire was on side of switch with part #s or something
    BACK TOGETHER
    1. Attach new cord to switch remembering wirers have to be in the same place as removed
    2. Replace restraining clip and 2 screws and tuck all wires in to saw
    3. Replace handle part watch that nuts stayed in place
    4. Inspect job should look just like it did but with shinny new cord
    PLUG IT IN, PULL TRIGGER (remember it IS a SAW and be careful )
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Power cord was frayed and needed replacement

    Fred - August 10, 2017
    👍 5 of 5 people found this instruction helpful
    Tool Type

    Miter Saw

    Difficulty

    Medium

    Time

    More than 2 hours

    Tools Used

    Screwdriver, Wrench Set, wire stripper and cutter

    1. Removed 4 phillips head screws to remove handle assembly from saw.
    2. Removed 5 phillips head screws to open handle assembly and provide access to wiring
    3. Removed power cord and its connection to a connector component and the switch.
    4. Cut new wires as needed to make connections
    5. Noted that the new strain relief was not the correct size. Discovered that this was due to the labeling on the miter saw which indicated that it was a model LS 1030 when it was actually a model LS 1030N. Was able to determine this from drawings which were accurate.
    6. Used old strain reliever which was in good condition
    7. Then disaster: One of the handle assembly screws fell into the armature casing. The armature unit could not be removed as it appeared to be stuck in the casing. This condition has been reported by others. After a couple of days trying magnets, shaking the casing, using wires, etc. I finally was able to see where the screw was stuck with a flashlight shining on the casing air vents. Once seeing the screw I was then able to remove it.
    8. Then took a little time to discover how a retention spring functioned together with the safety release button on the unit.
    9. Voila! Repair complete and the saw started and has been resurrected from the dead!!
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Needed a new cord

    James - March 10, 2017
    👍 3 of 3 people found this instruction helpful
    Tool Type

    Grinder

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver, Wire Crimping tool

    Remove the screws from the housing
    Remove the cord clamp
    Remove the cord wires from the switch
    Put strain relief on the new cord
    Connect the wire the switch
    Install the cord clamp
    Put the housing back together
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    cord worn out after 30 years

    alex - November 15, 2015
    👍 3 of 3 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    30-60 minutes

    Tools Used

    Screwdriver, Pliers, Power Drill

    Remove the handle cover to expose the cord, remove the two screws from the cord hold. Remove the cord leads from switch. It is easier if you remove the switch too. Slide off the cord relief and place it on the new cord. The cord does not include terminals for the switch. Attach cord to switch, replace switch and cord hold with the two screws. Attach handle half
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Repaired power cord, brushes and replaced flange nuts

    Aaron - November 30, 2015
    👍 2 of 2 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, wire crimpers

    Removed half of the switch handle, Remove two screws from cord holder, removed the the cord wires from the switch, cut the cord leads to the correct length, had to locate two terminals to put on the end of the cord leads. Attached cord leads to switch.don't for get to put the old cord relief back onto the new cord. reattached the cord holder with the two screws. Then replace the handle half. For the brush set, I removed the brush caps, then removed the old brush set and installed the new set and the brush caps. I also replaced the inner and outer flanges, and the blade bolt.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brother in law sawed through my power cord.

    David - January 22, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Medium

    Time

    30-60 minutes

    Tools Used

    Screwdriver

    1. Started figuring it out.
    2. Removed a couple more screws than necessary, removed the cover piece of shell.
    3. Took a good look at how the damaged cord was attached.
    4. Detached it.
    5. Fed in the new cord, using the attaching rings from the old cord (wish the new cord came with those rings already attached.
    6. Put the pieces back together.
    7. Actually, I had to do two saws - one circular and one reciprocating, so I repeated this process. Despite them both being Makita, the routing and attachment process was different. A very pleasant couple of hours one evening.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Needed new cord

    Joe - June 12, 2017
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver

    Take off the handle, take off the cord holder, take off the cord wires to the switch.
    Slide the new strain relieve onto the new cord. Cut the cord wires to the correct length. connect the cord wires to the switch. Screw the cord holder on. Screw the handle on.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Power cord worn out

    William - June 1, 2017
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Impact Wrench

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver

    Remove on half of the switch handle
    Remove the cord clamp
    Disconnect the cord wires
    Remove the cord relief from the old cord to the new cord
    Connect the cord wires
    Attach the cord clamp
    Replace the handle half
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Wire old, cracked and exposed.

    Phil - May 24, 2017
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Wire stripper and connectors.

    Separated handle and trigger section. This required removal of 5 screws. This exposed the wire connections. Removed old wire. It had a wire connector, sleeve type from a previous repair. This had to be reconnected. Threaded the wire thru the rubber wire protector. Made all connections, reassembled and tested. I put this off for ages. I had tried to fix it with electrical tape. Doing it right is always best!
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Saw would not start

    Phyllis - May 23, 2017
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Circular Saw

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Pliers, Nutdriver

    I already had removed my old parts while waiting for my new parts to arrive. There are 2 screws on the switch and 2 for the cord. Both parts were installed within 15 minutes. My favorite saw is new again.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.

    Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.

    Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.

    All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.

    This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.

    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal