866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  Makita Parts  664478-7 Power Cord (10-Foot)

Power Cord (10-Foot)

Part Number: 664478-7
Makita
Availability: 15 in stock
Price: $23.48
Quantity:
Order within the next 2 hours
and your part ships today!

*This part replaces obsolete part #: 664476-1 and 664479-5.

Specifications
Length: 10.0'
Gauge: 14
Wires: 2
Type: Eyelets
Description:
This power supply cord is a genuine Makita replacement part. It is a high quality item that is specially produced for circular and hypoid saws. It connects to a standard US outlet to supply power to the tool. This rubber insulated cord is sold individually. Please note, cord protector is sold separately. You will need a screwdriver to complete this repair.
Product Information
Manufacturer: Makita
Product Number: 664478-7
Classification: Part
Weight: 0.85 lbs.
Shipping: Ships Worldwide
Repair Guides
Watch the Repair Video for Power Cord
How to Replace the Cord on a Makita 5277B Circular Saw
Articles:
How to Replace the Cord on a Makita 5277B Circular Saw
This article will walk you through the steps required to replace a bad power cord on your Makita circular saw, which you...
February 24, 2013
Products Compatibility

This item works with the following types of products:

  • • Circular Saw
  • • Saw
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
1 of 1 people found this instruction helpful
Tool Type:
Circular Saw
Parts Used:
Power Cord (10-Foot) - 664478-7
Switch - 650103-6
Handle Set - 183525-0
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Switch quit working. Previously repaired plug end was arching.
1. Removed 6 screws on the handle of Makita saw.
2. Removed 2 screws on the bottom of the trigger switch to remove the 2 power wires to the motor.
3. Put right half of handle on the rear of the saw.
4. Hooked 2 power wires to the bottom of the trigger switch.
5. Removed 2 screws on top of the old trigger switch.
6. Installed new power cord on top of new switch using the 2 screws off old switch.
7. Routed wires in the new handle to avoid pinching, made sure pins in handle were lined up with holes in the switch.
8. Installed left side of the handle on the saw, put the 6 screws into the holes on the handle making sure cord lug is in the reversed area.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Power Cord (10-Foot) - 664478-7
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Power Drill
Bad cord
Removed casing
Followed wiring
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Power Cord (10-Foot) - 664478-7
Base - 168493-8
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set
Bent table, chopped cord
Makita hypoid saw. Put on new table, two bolts. Attached new cord, had to detach multiple screws to get into housing. Simple.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Power Cord (10-Foot) - 664478-7
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Power cord had exposed wires.
Undid screws on the handle, removed the old wires and replaced with the new one!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Cord Guard - 682505-8
Power Cord (10-Foot) - 664478-7
Hex. Flange Head Bolt M8X20 - 265315-4
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Power cord wires broke.
1. Remove screws.
2. loosen retaining bracket.
3. loosen screws for wires.
4. Modify wire to place under screw.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Power Cord (10-Foot) - 664478-7
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
I accidentally cut the power supply cord after completing a cut
Removed the screws to separate the handle of saw and access the cord connection. Disconnected and removed cord. The new cord is an exact replacement for my Mikita saw so just reconnected and screwed everything back in place. Easy fix for a dumb $30 mistake.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Power Cord (10-Foot) - ( 664478-7 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy