This is a genuine Porter Cable replacement part, it is sold individually. A Cord Strain Reliever is used on most all power tools. It purpose is to reduce the bending of the cord as it comes out of the housing, which otherwise would cause the cord to crack and wear.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
FITS, DOES THE JOB
FITS, DOES THE JOB
Guest - June 17, 2019
Verified Purchase
★★★★★
★★★★★
Works for multiple tools
I've used these on multiple tools with minor mods. Cutting the base flange into a square for a Porter Cable Router, shaving the base flange down a bit (thickness wise) for use on a Kett cutter.
Guest - June 25, 2019
Verified Purchase
★★★★★
★★★★★
Excellent
Great quality
Timothy - July 5, 2019
Verified Purchase
★★★★★
★★★★★
Perfect
Exactly as described...came fast and works great.
Guest - July 8, 2019
Verified Purchase
★★★★★
★★★★★
743 Porta Cable replacement electrical cord review
Parts was exactly what I needed. Need to include the electrical ends to fit the switch. Hard to find in hardware.
Guest - September 7, 2019
Verified Purchase
★★★★★
★★★★★
Easy to find parts, order
Using the website, it was very easy to find the small part for the sander that I needed and order it. The part was received promptly and fit perfectly.
Steven - May 23, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair with the correct part
Arrived on time and was the right part
Guest - May 25, 2020
Verified Purchase
★★★★★
★★★★★
Fit perfect
Part Fit perfect easy fix
Guest - June 14, 2021
Verified Purchase
★★★★★
★★★★★
Perfect fit
Perfect fit for my tool. It went in easily and fixed the problem.
Jim - June 16, 2021
Verified Purchase
★★★★★
★★★★★
Exact fit; easy repair
Perfectly pliable in order to provide the needed stress relief on cable/body intersection. Was very easy to install and fit/finish was exact.
Guest - September 21, 2021
Verified Purchase
< Prev
1
2
3
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed router top
2. Removed strain reliever retention bracket
3. Disconnected wires and pulled off old strain reliever from cord
4. Threaded cord thru new strain reliever
5. Reconnected wires
6. Replaced strain reliever retention bracket
7. Replaced router top
(there were a lot of router mode
... Read morels and several strain relievers to choose from ... make sure you have the correct part and things will go easy)
Read less
Did you find this story helpful?
Thank you for voting!
Cord had been cut so many times, strain relief was worn out
Removed side handle half, removed old cord, crimped new connectors on new cord, threaded cord through strain relief, reattached to switch, put handle half back on, put in screws.
Did you find this story helpful?
Thank you for voting!
Many parts were damaged or missing due to over 10 years of professional use.
Replaced the power cord and the work light. Replaced the pin that holds the saw in the closed position. Also replaced a few other misc parts. The light, power cord and pin were the biggest reasons I needed to repair just due to safety and ease of use. The pin was the hardest part to replace because I had to remove the large pivot pin
... Read morethat the entire saw hinges on by tapping it out with a mallet and a 1/2\" socket extension. The spring that holds the saw in the up position comes out when the hinge pin is removed making it extremely difficult to put everything back together. I realized after the fact that there are holes just below the spring that you can insert a screw driver or Allen wrench or similar object which holds the spring in the closed position. I still haven\'t figured out if there is an easier way to replace the spring itself since you obviously can\'t hold it in the closed position if you are trying to replace it, but my spring is fine and I don\'t have to worry about that now. There were no websites or videos that I could find to show how this is done, but I figured it out. Would have been easier if there was something that explained the holes for holding the spring before I took it all apart and the spring ejected the saw arm.
Removed handle half from sander, then removed switch. Remove cord wires from switch. Slid the new strain reliever on the new cord, attached the wires to the switch. Attached the switch to the switch handle, Assembled the handle assembly. Done
Remove handle cover, disconnect cord from switch. Remove worn reliever from cord. Slide the new reliever on to the cord. And connect cord leads to switch, then assemble handle cover.
1. Unscrewed the shell half\'s.
2. Unscrewed the power cord from the terminals.
3. Removed the old boot.
4. Installed the new boot.
5. Screwed the shell half\'s together.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
