Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy and fast replacement
This switch was easy and very fast replacement for my Bosch sander. It repaired a great sander and saved me from spending lots of $’s on a new tool!
Guest - June 19, 2019
Verified Purchase
★★★★★
★★★★★
Part was fine......wasn’t the problem!
The part was fine, arrived quickly and was not too difficult to install. Too bad it ended up not being the problem! Still not working. May be the little circuit board with the variable speed adjuster......
Ronald - January 4, 2020
Verified Purchase
★★★★★
★★★★★
Fast and easy
I have used E Replacement Parts for years and it is always easy to get what I need. It’s easy to find the parts and there quick to get them to me.
Thank You
Mel
Guest - February 5, 2020
Verified Purchase
★★★★★
★★★★★
Orbital sander down; need parts fast
Speed control came and was easily installed. Will order from you guys again!
Guest - August 13, 2020
Verified Purchase
★★★★★
★★★★★
You need it? They have it. Order with confidence. It will come on time and be what you ordered.
New condition, fit perfectly, and it works. All good!
Guest - September 16, 2021
Verified Purchase
★★★★★
★★★★★
Great part
Arrived quickly, perfect replacement, sander works fine
Guest - November 8, 2021
Verified Purchase
★★★★★
★★★★★
back to new
installation was a lot easier than expected. It now works like new.
Guest - September 13, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Unplug machine, look inside to assess problem. Mine showed melting of the trigger switch/power wire connection. Note location of all wires before disassembling. remove four wires and inspect...the melted one may need to be cleaned up. While machine is open, it\'s a good time to blow out all dust/clean with compressed air. Insert splices o
... Read moren two incoming power wires and reattach all four wires in original locations. Reassemble in reverse order.
Remove old pad by taking out one bolt. remove old friction ring (note orientation and just pull it off ) install new ring and sanding pad in reverse order.
Test your repair and have fun ! I have a sander that\'s good as new.
1. Removed cover from sander.
2. Popped out the old on-off switch.
3. Removed wires from old on-off switch.
4. Attached same wires to new on-off switch.
5. Secured 2 wire with screws from old switch.
6. Replaced cover and it works again.
1. Remove all screws securing the two halves of the housing
2. Seperate housing.
3. Use Air hose to clean housing and motor of dust, use a small brush to loosen any hard dust.
4. Loosen screws holding the feed conductors, armature, and field conductors.
5. Remove old switch and place new switch in recesses, attach
... Read moreconductors and reassemble housing, insert screws and tighten.
6. Test run, then put the sander to use.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP19509420
Manufacturer Part Number: 2607200260
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
