This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Perfect again
Ball bearing was an exact match of original and fit perfectly.
John - November 12, 2019
Verified Purchase
★★★★★
★★★★★
fit right
right parts.shipped fast
Robert - November 18, 2019
Verified Purchase
★★★★★
★★★★★
Fits and was as described
Quick delivery, good video to show how easy it was to fix.
Guest - December 24, 2019
Verified Purchase
★★★★★
★★★★★
Very easy repair
The shipping time was quick and had the driver fixed in less than 10 minutes.
Joe - April 26, 2020
Verified Purchase
★★★★★
★★★★★
Pricy, but they have what you need
Worked great
Guest - October 25, 2022
Verified Purchase
★★★★★
★★★★★
Worked as expected and my impact drill is working fine. I was not pleased with the shipping, the cost was totally unreasonable. Could have been sent through regular US POSTAGE for less than a dollar, yet you choose to bill me over $5!
Reveiw my comments about shipping. I was totally shocked at how you chose to shop! US Postage could have been used for less than $1, you choice was totally out of reason.
Guest - August 11, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Put grease down in hammer to hold the smaller ball bearings into place while I inserted the flat washer on top of the bearings. Then I inserted the
Compression spring on top of the flat washer ,Then I proceeded to put main shaft with the cup washer on it through the compression spring.I used the three jar puller to compress the sp
... Read morering in the assembly so shaft would push out through the hammer allowing me to put the two larger ball bearings in the two groves in the shaft. Once they were in place I released the pressure on the hammer spring and the assembly was now ready to it back in drill, be sure to apply a small amount of grease on the assembly before putting it back in the drill. Put the assembly back on the drill ,put the four screws back in tighten them down and you\'re done. I was very pleased with all the parts I received .Note : I downloaded the parts assembly of the hammer drill to make sure of the order which the parts went back in.
Put the ball bearings in place then put the sleeve and spring on and put the flat washer in place, you will need a very small screwdriver to snap the ring spring into place while compressing the flat washer down with a thumb or finger.
I used replacement parts on you tube to see how it was done to basically change out the anvil.
I then went to e-replacement parts.com to find the parts I would need.
Parts came in a good timely manner.. I hack sawed the socket off, unscrewed the impact driver casings, replaced parts, and put it back together. I did use the e
... Read more-replacement diagrams while doing this ,just to make sure I had it right..
I would use and recommend e-replacement parts to everyone in a heart beat, after all replacing something is much cheaper than buying a new one..
Thank you...
like a DA took apart standing in shop, so i lost 1 ball an spring ring. used grease to hold balls in place,replaced other parts,used screwdriver to push spring ring into place.
1. I reviewed the parts detail that your site provided.
2. I took the front part of the driver apart and identified the parts I would need for the repair.
3. I ordered the parts. They arrived within 3 days.
4. I installed the parts following the parts detail provided by the website.
5. The sleeve only goes on one
... Read more way to allow the flat washer to seat below the ring spring. If you are not careful the ring spring can fly off under tension as you take it off and put it back on.
6. The rest was easy. Works great and for $15 including shipping I saved a $100 replacement cost or repair bill.
Disassembled drive end, removed chuck (anvil) and put new one in. I had previously lost one of the lock balls, so put new one in. Very straight forward. Works like new.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10142080
Manufacturer Part Number: 216001-0
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
