This screw is a genuine Dewalt chuck screw. It is constructed of tough steel for long life. It has a beveled head with torx drive for a secure fit. This screw is reverse thread for securing drill chucks. It also has locking compound within the threads for an even tighter installation. This screw is commonly found in Dewalt cordless drills and it is compatible with the tools listed below. It is not guaranteed to fit any other power tools.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Awesome
Easy to shop and find products. Fast shipping.
Thank you
Multiple times user
Thomas - June 4, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair, good quality
Fits my dewalt drill perfectly
Guest - June 5, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit.
Used to secure drill chuck, had a locking sealant on threads, perfect fit.
Guest - August 13, 2019
Verified Purchase
★★★★★
★★★★★
part as described just what I needed
I have ordered parts from you before and recieved great service and quality parts each time. you are thr first place I look for my needs. AAAAA+++++
Guest - November 4, 2020
Verified Purchase
★★★★★
★★★★★
it was a reverce thread screw , hard to find , worked great
easy to order , came fast , it was the right part , great job ..
Guest - April 19, 2021
Verified Purchase
★★★★★
★★★★★
Great place to do business with.
Thank you for the great service I only needed a very low cost part but they handled it like I spent $1,000.00 that’s a company I’m going the give future business to.
Guest - July 12, 2021
Verified Purchase
★★★★★
★★★★★
DeWalt Chuck Replacement
Right part, delivered timely, great price, great on line service. Well done.
Guest - December 29, 2021
Verified Purchase
★★★★★
★★★★★
Perfect part, excellent customer service
Replaced existing part like new. Customer service from E replacement parts was top notch
Guest - February 11, 2022
Verified Purchase
★★★★★
★★★★★
Always the right parts, simple repair
Replacement chuck and reverse screw arrived on time. Online instructions were very helpful. My old drill works perfectly. Thanks Again!
Victoria - April 20, 2022
Verified Purchase
★★★★★
★★★★★
good part.scipping was slow
good part.scipping was slow
Guest - June 7, 2022
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove broken screw and replace. The repair was easy enough to complete but the reason I submitted this form is to let people know of the excellent service from \"ereplacementparts.com\". these folks give prompt and courteous service and have very reasonable prices. I would highly recommend this supplier to anyone needing power tool parts
... Read more.
My original Dewalt chuck was stuck and warranty was expired. I searched for the original chuck and the reverse screw online until I came up with ereplacementparts.com. What a relief, got my parts fast and fixed my cordless drill. Thanks ereplacementparts.com.
Use a torx t-20 to remove the LH thread in the chuck.
Get largest allen wrench you have
Put the small end off the allen wrench in the chuck and tighten it up.
Place the speed of your drill on low and in the drill position.
Lay the drill on its side and strike the allen wrench with a hammer to loosen the chuck fro
... Read morem the spindle.
Remove the old chuck.
Then install the new one.
I removed the LH threaded chuck screw with a torx bit. Placed the short end of the largest allen wrench I could fit into the chuck and tightened the chuck. Put the drill in low speed and in the drill mode. Laid the drill on its side and hit the allen wrench with a mallet to remove it from the spindle. Removed the chuck from the spindle ,t
... Read morehen threaded the new chuck on, then screwed the new chuck screw in, to hold the chuck on.
The chuck screw had become loose inside of the chuck. Turn the screw clockwise to tighten it. You may want to put on some Loctite blue on the threads to keep it tight in the spindle. The screw is a Torx T-20.
Removed front housing,
Used snap ring pliers to remove snap ring,
Used different sized sockets on bench vise to remove broken spindle and front housing bearing.
By using sockets to straddle spindle and slowly tightening vise it works like a manual press and spindle pushes out easily.
Bearing and spindle can then b
... Read moree installed using same idea.
Read less
Did you find this story helpful?
Thank you for voting!
Screw snapped when drill bit became stuck and I tried to back it out in reverse and the screw holding the chuck in place snapped.
I removed the chuck and and using pliers I turned the screw clockwise until it was fully out. I then returned the chuck and put the new screw in the middle using a screwdriver.
Removed old chuck and replaced. Very simple. Much cheaper than replacing drill
eReplacement has very good service,very expedient,always the right part,and easy to find on their site and fair prices to go along with it.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10180947
Manufacturer Part Number: 605256-01
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
