Genuine Ridgid replacement part, this item is sold individually. The main function of the Inlet Reed Valve is to allow air in to the air tank once the air has been pumped in the pump cylinder and piston. Once the compressor reaches its max PSI, The motor and pump will shut off. At this point the Inlet Reed Valve will close , not allowing any air in the tank to leak back into the pump. The symptoms of a bad Reed Vale is hearing an air leak and the compressor not coming up to the shut off PSI.
This is a Genuine Manufacturer Sourced replacement part designed for use with Ridgid Air Compressor. This part is made out of Metal and it is Sold Individually. Reed valves are commonly used in high-performance versions of the two-stroke engine, where they control the fuel-air mixture admitted to the cylinder. As the piston rises in the cylinder a vacuum is created in the crankcase beneath the piston.
This drain valve is an OEM part direct from Ridgid and is used on a gas powered compressor. The purpose of the drain valve is to allow moisture to be removed from the tank. Please note each tank has its own drain valve each is sold separately and made of a durable high-quality metal.
This is a genuine OEM sourced replacement valve kit designed for use with Campbell Hausfeld air compressors. The purpose of the valve plate is to allow air into the cylinder. Once the piston starts traveling up the reeds on the valve plate open and the air is sent into the tank. Over time valves and gaskets will become worn and would need to be replaced to keep your equipment running well. To complete this repair you would need a wrench set and a screwdriver to take off the housing and the cylinder head. Keep in mind this high-quality valve plate assembly is made of durable metal and is sold as an individual component.
The relief valve attaches to the discharge T. This item is available as an individual replacement part. It is a genuine OEM sourced part which is specially designed for use with Ridgid compressors. A wrench set may be needed during the replacement of this part. The valve is made out of metal and will need to be replaced if it breaks.
This is a genuine OEM part. The Ridgid pressure unloader is compatible with the GP80145SW 8 Gallon Gas Wheelbarrow Air Compressor. The metal component helps to secure the gauge panel hose, throttle and elbow. The pressure unloader assists with decreasing the pressure from the compressor tank. This component is sold individually. A wrench and pliers are helpful with making the installation. Please refer to the manual for further safety and repair instructions.
It is a genuine item that is supplied by the original equipment manufacturer for use with Ridgid air compressors. This is an identical replacement for a missing or damaged non-return valve that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.
This is a genuine Ridgid replacement part that has been sourced from the original manufacturer to be used with air compressors. The metal check attaches to the tank. This item is used to allow air from pump head into the tank, and to prevent the air from exiting even when the unloader is open. A pair of pliers and a wrench are needed to install this part and it is sold individually.
It is a genuine OEM sourced part which is specially designed for use with Ridgid compressors. The unloader attaches to the pressure switch. An allen wrench may be necessary during the installation of this item. It is made of plastic and metal and will need to be replaced if it breaks. This part is available as an individual replacement.
This is an authentic Ridgid replacement part that has been sourced from the original manufacturer to be used with air compressors. The metal two-way valve is used as a coupler to pass air between two pipes. This part may require a wrench set to install and is sold as an individual replacement part.
The discharge T attaches to the relief valve and is made of metal. This is a genuine replacement part sourced from the original manufacturer for use with Ridgid compressors. This part is available individually. When replacing this part a wrench may be needed. It will need to be replaced if it breaks.
The valve plate attaches to the seat valve and is made of metal. This is an original Ridgid part for use in compressors. It is available as an individual replacement part even though more may be needed. During replacement, it may require a screwdriver to help install this item correctly. This part may become broken and will need to be replaced.