866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  MK Diamond Parts  152227 Multilube Bearing

Multilube Bearing

Part Number: 152227
MK Diamond
Availability: 20 in stock
Price: $2.99
Quantity:
Order within the next 7 hours
and your part ships today!
Description:
This is a Genuine MK Diamond replacement part, it is sold individually.
This Bearing is installed in the hole provided on the cutting table.
It slides on the rail when the table is moved to produce a cut.
It is a phenolic bearing for the reason a metal bearing would not last long with the presence of water that it comes in contact with.
There are two of these bearing used on the saw models shown below.
They do have a tendency to wear, it is advised to have a couple of these on hand.
Product Information
Manufacturer: MK Diamond
Product Number: 152227
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide
Related Products
Products Compatibility

This item works with the following types of products:

  • • Saw
  • • Tile Saw
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
8 of 8 people found this instruction helpful
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set, Flat end punch, hammer
Table would not slide smoothly, would bind easily when pushed from anywhere but directly in-line with the slide rail
The table and slide rail come off easily with the removal of 1 - 1/4x20 bolt on each end. Take rail cover off and slide chromed rod out of the table bearings. Old bearings punched out easily using a 12" length of 1/2" dia rod, Set the table up on end and hold in a vertical orientation with in a vise or c-clamp, Put rod through the upper bearing boss and set lower end of punch on the edge of the bearing in the lower boss. alternate back and forth between opposite sides of the bearing and tap it out a little at a time. Flip table over and repeat for the second bearing. Clean boss bores and start new bearings into bore holes by hand, finish inserting with a c-clamp, squeezing bearing into holes as the clamp is tightened. Install slide rod back into bearings and re-install into saw frame making sure to adjust the slide rod on both ends to make sure the carrier roller on the outside of the table is centered on the outside rail. Final results were less than I had hoped for. Table still binds when pushed from the center or the outside edge even when wet. However it does slide more smoothly when pushed from the left side, in line with the bearings and the slide rod. This may be a design flaw. I got the saw used and have never experienced how it worked when new. The slide rod is highly polished chromed steel and doesn't show any signs of wear or roughness so I can't explain the binding other than the possibility that the slide rod may be bending slightly when pushed from the outside. It works well enough that I am not motivated to continue troubleshooting for now.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Wrench Set, Hammer
Bad multilube bearing i changed both
I removed the two 1/2" bolts that retain the guide rod and then slid the rod out of the bearings.
Then with a hammer and screw driver removed the bearings and re-inserted the new ones.
Then I reversed the procedure and put it back together. Lining up the rod so it cuts straight.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Tile Saw
Parts Used:
Wing-Screw, 1/4-20 X 1/2 - 151888
Wing-Nut, 5/16-18 Nylock - 151746
Roller Wheel - 151799
Multilube Bearing - 152227
Splash Guard - 160310
Ball Bearing - 137711
Bumper, 1/2 Dia Rubber - 152674
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, Adjustable Wrench
Refurbish MK 101 tile saw
Used 3 jaw puller to remove old bearings. Cleaned the shaft with emery paper and used rubber mallet to install new bearings.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Socket set, Dead-blow hammer
1. Removed the slide table
2. Drive out old multi-lube bearings
3. Install new multi-lube bearings
4. Reinstall the slide table
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Splash Guard - 160310
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Power Drill, Socket set, 1/4-20 tap and twist drill/ C Clamp/ square
Guides for sliding table warn out. Splash guard missing
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Socket set
Nothing was wrong.
Easy repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Wrench Set
Table would not slide correctly.
1. Removed the two bolts at the end of the slide.
2. Removed the table swap out the bearings.
3. Reinstalled and squared up the table.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Multilube Bearing - 152227
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Wrench Set
Bearing worn.
1. Removed the slide table.
2. Installed the slide bushing.
3. Reinstalled the slide table.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Tile Saw
Parts Used:
Plug, Water Drain - 159529
Multilube Bearing - 152227
Splash Guard - 160310
Blade, MK-100, 10 X 060 X 5/8 - 154380
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Adjustable Wrench, WD40
Plate would not slide smoothly which caused tile to cut unevenly
Took apart arm that operates plate that holds tile and replaced bearings, cleaned bar.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Multilube Bearing - ( 152227 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: Mk101 Change Bearings In Table

1370555

how do I change the bearings in the cut table
WJA
Hello 1370555,

There are a couple of ways to remove the 152227 Multilube Bearing from the 157660 Table.

1- If you have a socket the same size of the bearing, you can tap it out with a mallet.

2- You can use a screwdriver and catch the edge of the bearing and again tap it out.

To replace the bearing, line it up straight with the hole in the table and tap lightly with a mallet into the hole. It should go in fairly easy.

-WJA
Question: Loose Bearings

1222327

I have a MK-370EXP tile saw. Both of the bearings have come loose from platform. The part number is 152227. I can no longer cut tile without the bearings sliding out of the platform. Can I reattach the bearings that I have or do I need new ones?
WJA
Hello 1222327,

After time the 152227 bearings will wear out. The best thing to do is replace them.

-WJA
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy