Motor Housing 1619PA8038
Part Number: 1619PA8038
Order within the next 7 hours
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: 2610018981 and 2610996864.
Product Information
Description:
This is an original Bosch replacement motor housing kit. It is specially manufactured to replace the electric motor housing used on table saws. It includes a plastic housing cover, two carbon brush holders, two brush caps and three screws. Please note, the end cap, brushes and other parts are all sold separately. Replacing this housing is a simple task that should only require a screwdriver set. • Make sure to unplug the equipment first • Remove the end cap • Remove brush caps and brushes • Remove the old motor housing • Secure the new housing in place • Reassemble and test the saw |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
the 16 compatible machines
Products Compatibility
This item works with the following types of products:
- • Saw
- • Table Saw
Questions & Answers for Motor Housing
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
5 of 5 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Power Drill, Socket set, Wrench Set, Hex wrench
Loud, high-pitched squeal, then motor would not start after cooling down
I surmised a bearing issue and validated my idea via internet searching for Bosch T-4000 table saw maintenance, finding several articles on bearing, brush, armature, and field replacement, but no articles on performing bearing lubrication or maintenance. e-Replacement had very good diagrams of the saw and saw motor, so I removed the motor and found the bearing on the commutator end of the armature badly burned and rough, the rubber ring melted and the end of the motor housing melted. I ordered the parts and when they arrived, I replaced the bearing, rubber cap that holds it securely in the motor housing, the housing itself, the brushes (even though they looked to be in fairly good shape and just slightly chipped on one edge), and transferred the necessary parts from the old housing.
The armature and the field both had a thin layer of the melted rubber ring and the melted end of the housing over much of their metal surfaces which I carefully sanded off with very fine Wet-or-Dry sandpaper (armature and commutator) and a cylinder hone (for the field).
The hardest part was fitting the motor housing end cap back onto the motor housing due to the very limited space and getting the wires and butt-joints into their exact locations so that the cap fit back on and seated into place. I used an old bicycle spoke to prod the wires and butt-caps into place to get everything aligned. Take a picture, take notes, or make a drawing of how the wires fit in the cap if or when you remove it from the motor housing to save yourself the time it took me.
I have now ordered the other 3 bearings in the motor, though the rest seem okay and I was able to carefully pry out the seal from the other armature bearing and refill it with grease before putting everything back together.
I will also try to seal any excess holes in the housing for the vacuum port so that I can keep the motor cleaner. I will also always connect a vacuum hose from my Dust Deputy and shop vac when using this saw to keep sawdust out of the motor.
The armature and the field both had a thin layer of the melted rubber ring and the melted end of the housing over much of their metal surfaces which I carefully sanded off with very fine Wet-or-Dry sandpaper (armature and commutator) and a cylinder hone (for the field).
The hardest part was fitting the motor housing end cap back onto the motor housing due to the very limited space and getting the wires and butt-joints into their exact locations so that the cap fit back on and seated into place. I used an old bicycle spoke to prod the wires and butt-caps into place to get everything aligned. Take a picture, take notes, or make a drawing of how the wires fit in the cap if or when you remove it from the motor housing to save yourself the time it took me.
I have now ordered the other 3 bearings in the motor, though the rest seem okay and I was able to carefully pry out the seal from the other armature bearing and refill it with grease before putting everything back together.
I will also try to seal any excess holes in the housing for the vacuum port so that I can keep the motor cleaner. I will also always connect a vacuum hose from my Dust Deputy and shop vac when using this saw to keep sawdust out of the motor.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, allen key, snap ring pliers, gear puller/installer
The rear bearing on the armature seized and the resultant heat melted a section of the motor housing causing the table saw to lock up.
Bosch 4000 table saw repair. Remove the rear motor housing (3 Phillips screws) then uncrimp the 3 wires attached to the field winding/carbon brushes. The next step is to remove the four phillips screws that hold the motor housing to the inner gear box. Pull housing towards you to remove. I used a gear puller to remove the bad armature bearing, then proceeded to degrease and clean the armature with electromotive cleaner. Reassembly is the reverse of disassembly.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Wrench Set, Nutdriver
bearing on armature seized up and cooked end of motor housing
a local industrial tool repair shop had the needed bearings instock , removed and pressed on the new parts . e replacementParts had the housing in stock. My order was shipped and received in a couple of days,I completed the repair, my saw is back up and running. Great reliable service as always. I am a repeat customer . Thanks !
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Socket set, Wrench Set, Bearing Puller
The rear bearing spun and burnt the motor housing seat out of round.
I had to remove the motor from the saw. Remove the armature, disconnect the field wires and remove the field, Remove the bad bearing from the armature shaft and replace it with a new bearing. Install the field and rewire, install the armature in the housing, and install the motor to the saw. Repair complete.
The only tricky or hard thing with this repair is reinstalling the speed control board and rewiring. You have to use the same size small wire nuts when you rewire the field and brushes because you have very tight tolerances.
The only tricky or hard thing with this repair is reinstalling the speed control board and rewiring. You have to use the same size small wire nuts when you rewire the field and brushes because you have very tight tolerances.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Power Drill, Ball bearings puller
Wasn’t running
I removed the motor housing, and the ball bearing… replaced with the new ones, put it back together!..
That was it!
It is running again!
That was it!
It is running again!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Roto Zip
Rear bearing on armature froze up.
Removed old motor housing.
Replaced motor housing, armature, bearing, ball bearing, rubber ring, and carbon brushes.
Installed new motor onto saw.
Replaced motor housing, armature, bearing, ball bearing, rubber ring, and carbon brushes.
Installed new motor onto saw.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Bearing puller
Rear bearing froze on the motor.
1. Removed the bearing.
2. Cleaned out the armature.
3. Installed the new bearing.
4. Installed the new brushes.
5. Installed the new motor cover/casing.
2. Cleaned out the armature.
3. Installed the new bearing.
4. Installed the new brushes.
5. Installed the new motor cover/casing.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
2 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Bosch motor housing
Worked as it should. Great part
Guest -
April 27, 2021
Verified Purchase
Great service and parta
Customer service was very helpful in assisting me with parts ordering. Parts mounted correctly and installed easily. Great site!
Guest -
June 7, 2020
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information