866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Grill Parts  Char-Broil Parts  G527-2200-W1 Main Burner For Firebox

Main Burner For Firebox

Part Number: G527-2200-W1
Char-Broil
Availability: 25+ in stock
Price: $14.81
Quantity:
Order within the next 14 hours
and your part ships today!
Description:
This is a genuine Char-Broil replacement part, it is sold individually. Depending on your grill you may have 3 or 4 of these burners. This burner comes with Two (2) Cotter Pins. The burners are the part of the grill that the flame rises from. The Burners flame is controlled by the control knobs that are attached to the Valve/Manifold/Regulator. It is recommended to keep these clean and covered as they have a tendency to rust and corrode.
Product Information
Manufacturer: Char-Broil
Product Number: G527-2200-W1
Classification: Part
Weight: 0.53 lbs.
Shipping: Ships Worldwide
Repair Guides
Articles:
How to Replace the Ignitor Button on a Char-Broil Tru-Infrared Gas Grill
Having trouble getting your grill to light up? A common cause of this issue is a defective ignition switch. We'll sho...
November 08, 2012
Related Products
Questions & Answers

what is the length and diameter of burner?
cathy broussard
Hello Cathy, Thank you for the question. The burner is approximately 15.85"L but unfortunately we do not have access to the diameter sorry. Hope this helps, good luck with this repair!
Repair Instructions: Submitted by Customers Like You
7 of 8 people found this instruction helpful
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner For Firebox - G527-2200-W1
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Pliers
Main burners rusted out bad.
Simply remove parts to get to burners, disconnect starter with screwdriver, remove old cotter pins with pliers, install new parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
5 of 6 people found this instruction helpful
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner Electrode - G350-0064-W1
Main Burner For Firebox - G527-2200-W1
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Pliers
The burners and the crossover tubes on the grille were rusted through causing severe hot spots in some reason and overall undesired operation. I replaced the ignitor electrodes because they were inex
1. Shut off and disconnected the LP supply.
2.Removed the Grille grate and the 4 heat deflectors.
3. Removed retainer clips holding burners and cross over tubes.
4. Pulled burner tubes partially away from control valve and disconnected ignitor electrodes.
5. Removed all 4 burners tubes and 3 crossover tubes.
6. Unplugged the ignitor electrodes from the Spark module.
7. Took the opportunity to clean the inner fire box and inspect for any other signs of wear and tear.
8. Routed 4 ignitor electrodes through valve holes in firebox and plugged them on to the spark module
and snapped the other end of ignitor electrodes on to burner tubes.
9. Installed crossover tubes and clips onto burner tubes.
10. Reinstalled LP supply and checked operation.
11. Shut off grille and Reinstalled heat deflectors and grate.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Outdoor Grill
Parts Used:
Main Burner For Firebox - G527-2200-W1
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Pliers
Low flame height.
1. Removed and cleaned grates.
2. Removed and cleaned infrared plates.
3. Removed heat shields.
4. Removed pins holding burners.
5. Removed burners.
6. Cleaned around inside firebox.
7. Put in new burners.
8. Put in new pins.
9. Turned on propane and tested.
10. Everything worked great.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner For Firebox - G527-2200-W1
Heat Tent - G455-0009-W1
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Old parts were rusted out from years of use.
Parts fit as direct replacements, just remove old parts and clean grill while parts are out of the way, reassemble with the new parts. My grill works like new again was real easy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner Electrode - G350-0064-W1
Main Burner For Firebox - G527-2200-W1
Repair Difficulty:
Easy
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers
Burner and associated parts were rusted, not heating properly
This was a very simple repair.
Remove old rusted parts.
Minor clean up of the burner area.
Install replacement parts.
Everything fit in place correctly without modification.
Test for proper operation - good to go!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner For Firebox - G527-2200-W1
Heat Tent - G455-0009-W1
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers
4 main burner tubes, carry over tube assembly and heat tent were rusted and not functional
1 Removed all rusted parts to be replaced and cleaned fire box with Shop Vac. This was done prior to placing order which helped me determine exactly what I needed. Approximately 30min.

2 When I received the parts I started with the main burner tubes following the instructions included each tube was inserted and a cotter pin placed on the back end of each tube secured them. Needle Nose pliers made this easy.

3 The carry over tube assembly was next but before you can complete this part you need to screw a small eyelet screw in the front of each burner tube. When this is completed the carry over tubes can be put in place and secured with a cotter pin.

4 The final step was to place the 4 heat tents over each burner. They simply fit into a niche in the fire box over each burner. Approximately 30 min.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Flame Carryover Tube - G524-0036-W1
Electronic Ignition Module - G515-0030-W2
Main Burner Electrode - G350-0064-W1
Main Burner For Firebox - G527-2200-W1
Infrared Emitter - 80021358
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers
Internals rusted out
Removed the grill grates and cleaned them
Removed the heat emitters and tossed them
Removed the flame tamers and cleaned them
Unplugged the burner electrodes and removed the rusted out burner tubes
Completely cleaned out the main box
Attached the new igniters to the new tubes and replaced the tubes
Ran the wires to the new ignition module and attached them
Attached the flame carryover tubes
Started the grill, testing each burner
Reset the flame tamers, heat emitters, and grill grates
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Flame Carryover Tube - G354-0024-W1
Main Burner For Firebox - G527-2200-W1
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers
Burners and cross over tube were rusted and falling apart. Nothing was working as it should.
Took all the grates off grill, then removed the burners and cross over lighter. Not to difficult cause of rust and decay. New parts worked great as they were charbroil grill parts. Bad thing is I saw other repairs that will be needed to be addressed. Everything went smoothly and parts were shipped as promised.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Temperature Gauge - G515-0031-W1
Main Burner For Firebox - G527-2200-W1
Heat Tent - G455-0009-W1
Cooking Grate - G455-0008-W1
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Drift
Gas grill had hot spots , holes in burners, rusty grates, and thermometer was not accurate
Removed old parts and installed new.....they were just like the original parts so it made the repair much easier. The parts are more reasonably priced than the big box stores parts and are factory correct
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube Assembly - G614-0095-W1A
Main Burner For Firebox - G527-2200-W1
Heat Tent - G455-0009-W1
Cooking Grate - G455-0008-W1
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Used a center punch to remove old spring clips.
Rusted parts
Very happy with this product. Saved hundreds of dollars by not having to replace our grill.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Main Burner For Firebox - ( G527-2200-W1 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy