Medium
1-2 hours
This is an authentic Poulan replacement part that has been sourced from the original manufacturer to be used with chainsaws. The gasket kit includes two carburetor and one muffler gaskets. It is recommended to replace gaskets when servicing the chainsaws to ensure the parts are sealed when they are reassembled. The kit will include all three gaskets.
Kit Gasket Engine 576752501
OEM part for: Poulan
Part Number: 576752501
$4.99
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Poulan
PP5020AV 2 Stroke Gas Chainsaw View Diagrams & Manuals
PP4818A Chain Saw View Diagrams & Manuals
This item works with the following types of products:
- Chain Saw Parts
- Saw Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Kit Gasket Engine
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
No Compression, won't start
Robert - December 30, 2016
👍 2 of 3 people found this instruction helpful
Tool Type
Chain Saw
Difficulty
Medium
Time
More than 2 hours
Tools Used
Pliers, Socket set, Nutdriver
Removed carb, exhaust, and coil.
Removed head
Removed piston
Replaced piston
Replaced head
Replaced carb and exhaust
Needed to purchase high temp RTV for the gasket between the cylinder head and crank case. There is no gasket on parts list for a gasket here.
Removed head
Removed piston
Replaced piston
Replaced head
Replaced carb and exhaust
Needed to purchase high temp RTV for the gasket between the cylinder head and crank case. There is no gasket on parts list for a gasket here.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would start and run at half-choke, but wouldn't throttle up.
Jim - March 4, 2023
Tool Type
Chain Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
, Torx bit
Removed to cover, two machine bolt through carburetor, one screw through choke housing. Youtube video was very helpful.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
There was no compression - piston scratched
RAymond - May 5, 2022
Tool Type
Chain Saw
Difficulty
Hard
Time
More than 2 hours
Tools Used
Screwdriver, Socket set, Wrench Set, Nutdriver
1) stripped every part off of saw to reveal cylinder assembly.
2) opened up cylinder assembly and removed piston and crank shaft
3) installed new piston and cylinder assembly.
4) reinstalled parts in reverse order of removal
5) be sure to align fly wheel using markings on bottom with markings on shaft.
6) repair was successful
2) opened up cylinder assembly and removed piston and crank shaft
3) installed new piston and cylinder assembly.
4) reinstalled parts in reverse order of removal
5) be sure to align fly wheel using markings on bottom with markings on shaft.
6) repair was successful
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Saw would not start.
david - June 11, 2018
Tool Type
Chain Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Socket set, Hex bits, scraper and chain saw multi tool.
1 Removed bar and cover
2 Removed side cover and top cover from saw
3 Removed spark plug and removed machine screws for carb.
4 Disconnected choke and throttle linkage.
5 Remove screws for carb adapter to engine.
6 Removed carb assembly, scraped gaskets off and installed new carb.
7 Reattached linkage and fuel lines. Make sure purge valve is in slot correctly.
8 Removed spark arrestor and installed new gasket after cleaning out carbon.
9 Reinstall covers, plug, air filter and bar.
10 Fuel and start. It works.
2 Removed side cover and top cover from saw
3 Removed spark plug and removed machine screws for carb.
4 Disconnected choke and throttle linkage.
5 Remove screws for carb adapter to engine.
6 Removed carb assembly, scraped gaskets off and installed new carb.
7 Reattached linkage and fuel lines. Make sure purge valve is in slot correctly.
8 Removed spark arrestor and installed new gasket after cleaning out carbon.
9 Reinstall covers, plug, air filter and bar.
10 Fuel and start. It works.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bad gasket
cheryl - May 4, 2018
Tool Type
Chain Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
Replaced gasket on carburetor; bought the gasket kit so that I could replace all gaskets at one time,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Engine would not start which was determined to be due to low compression.
Jonathan - January 19, 2019
👍 0 of 1 people found this instruction helpful
Tool Type
Chain Saw
Difficulty
Medium
Time
More than 2 hours
Tools Used
Screwdriver, Socket set, Wrench Set, Allan wrenches and star drivers
Dismantled the saw down to bare cylinder for replacement. Replaced the piston ring but not the piston or piston rod. Clutch sprockets were badly worn so it was also replaced. Internet was a help on how to remove the clutch. Removing the handle vibration spring off the cylinder head was a challenge. After several attempts I determined it was attached with a star headed bolt (could not see it through the small hole in the spring end plate). The shaft on the star driver was larger than the hole so it was drilled to a larger hole. The bolt and spring were then easily removed and reattached to the new head. Since the handle is attached to the tapped spring end plate that was drilled out, a larger fastener was used to accommodate the larger hole. After the repair the engine easily started and runs fine. Lesson learned was that it can be more than a fuel or ignition spark issue as a reason the engine would not start.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
