Insulator Gasket 20A-35902-03

Needle - 277-62500-08

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set

Carb had dried up gasoline in it. Parts needed for overhaul

Disassemble, soak carb in solvent , reassemble. Start snowthrower cold. Ran good. Return to customer

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Packing - 277-32604-08

Insulator - 20A-32902-01

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set, Gasket scraper

The carburetor had the wrong gaskets on it causing it to suck air and lose power at full throttle

Removed the 2 nuts and one bolt using a 10mm socket from the air cleaner, slide the housing off
2.remove carburetor
3. Remove insulator
4. Peal off and use gasket scraper to clean up any old gasket material stuck to engine; insulator; carburetor; and air cleaner housing
5.install insulator gasket, insulator, carburetor gasket, carburetor, air cleaner gasket, and air cleaner housing; put the 2 nuts and 1 bolt to secure everything back down properly

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Gasket(muffler) - 277-35201-13

Bolt - 277-62360-08

Screen Cp - 277-37203-H1

Muffler Cp - 20A-30101-01

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver

Gas was leaking out of my Robin carburetor on my Subaru engine on my Rigid Pressure Washer.

1. Drained the fuel tank
2. Removed air cleaner assembly
3. Removed carburetor assembly and fuel line
4. Replaced muffler and associated parts
5. Replaced gaskets and o-rings in carburetor and started reassembly

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Packing - 277-32604-08

Cover Cp - 277-32602-18

Element - 277-32603-08

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Pliers, Socket set, Wrench Set

Bad carburetor

Replaced the mounting gaskets, carburetor, filter and cover for filter.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Needle - 277-62500-08

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Socket set, Wrench Set

Would not run!

Pulled carburetor off. Soaked in carburetor cleaner overnight. Pulled all jets out and cleaned them. Oxygen and Acetylene Tip Cleaning tool used to make sure all jets were clean. Replaced the needle valve. Installed new gaskets. Runs!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Socket set

Carb bowl leaking fuel

Removed carb bowl
Installed new gasket
Reinstalled bowl

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Pliers, Wrench Set

Carburator

Put new carb on and started right up easy job

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Element - 277-32603-08

Hose Clamp - X56-11100-60

Carburetor Assembly - 277-62301-60

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set, Wrench Set

lpressure washer rope broke

Exactly how you stated here before it cliked and disapered

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, Adjustable Wrench

Old gas in carb and tank

1. Removed carburetor
2. Disassembled carburetor and cleaned parts
3. Replaced gaskets and reattached carburetor
4. Cleaned gas tank after draining old gas out
5. Added new gas and it started right up
6. Ran engine with gas shut off till it stopped

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used: