Medium
30-60 minutes
This fuel line is a genuine OEM part, not an aftermarket equivalent. It is used on Husqvarna chainsaws to supply the fuel. This hose is connected to the carburetors primer bulb and the fuel filter. Over time fuel lines tend to deteriorate and crack allowing for leaks. A damaged or brittle line should be replaced immediately. Please note, it is sold individually, (1) hose per order.
Hose 537042408
OEM part for: Husqvarna, Jonsered
Part Number: 537042408
$7.46
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 40 machines
Husqvarna
455 E (2007-01) Chainsaw View Diagrams & Manuals
455 E (2006-06) Chainsaw View Diagrams & Manuals
455 (2004-10) Chainsaw View Diagrams & Manuals
455 (2005-01) Chainsaw View Diagrams & Manuals
455 (2005-03) Chainsaw View Diagrams & Manuals
455 Rancher (2006-02) Chainsaw View Diagrams & Manuals
455 (2006-06) Chainsaw View Diagrams & Manuals
455 (2007-01) Chainsaw View Diagrams & Manuals
460 (2005-03) Chainsaw View Diagrams & Manuals
460 (2006-02) Chainsaw View Diagrams & Manuals
460 (2006-06) Chainsaw View Diagrams & Manuals
460 (2007-01) Chainsaw View Diagrams & Manuals
334 T (2003-05) Chainsaw View Diagrams & Manuals
334 T (2003-11) Chainsaw View Diagrams & Manuals
334 T (2004-01) Chainsaw View Diagrams & Manuals
334 T (2005-03) Chainsaw View Diagrams & Manuals
334 T (2006-01) Chainsaw View Diagrams & Manuals
334 T (2006-09) Chainsaw View Diagrams & Manuals
338 XPT (2003-05) Chainsaw View Diagrams & Manuals
338 XPT (2003-11) Chainsaw View Diagrams & Manuals
338 XPT (2004-01) Chainsaw View Diagrams & Manuals
338 XPT (2005-03) Chainsaw View Diagrams & Manuals
338 XPT (2006-01) Chainsaw View Diagrams & Manuals
338 XPT (2006-09) Chainsaw View Diagrams & Manuals
356 BF (2004-10) Blower View Diagrams & Manuals
356 BT (2004-10) Blower View Diagrams & Manuals
350BF (X-Series)(2004-10) Backpack Blower View Diagrams & Manuals
356BT (X-Series)(2004-10) Backpack Blower View Diagrams & Manuals
356BF (X-Series)(2009-07) Backpack Blower View Diagrams & Manuals
356BT (X-Series)(2009-07) Backpack Blower View Diagrams & Manuals
460 (2011-01) Rancher Chainsaw View Diagrams & Manuals
461 Chain Saw View Diagrams & Manuals
460 Rancher Chainsaw View Diagrams & Manuals
Jonsered
CS2135 T (2005-03) Chain Saw View Diagrams & Manuals
CS2135 T (2007-01) Chain Saw View Diagrams & Manuals
CS2139 T (2008-02) Chain Saw View Diagrams & Manuals
CS2139 T (2010-03) Chain Saw View Diagrams & Manuals
CS2255 (2008-03) Chain Saw View Diagrams & Manuals
CS2255 (2009-03) Chain Saw View Diagrams & Manuals
CS2255 (2011-01) Chain Saw View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Chain Saw Parts
- Saw Parts
- Blower Parts
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
2
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Great Replacement Part
The part was in great condition, perfect fit, and my Husqvarna 455 Chainsaw functions as new.
Guest -
October 9, 2021
Verified Purchase
It worked
Good part
David -
August 9, 2021
Verified Purchase
It was the original replacement part
The part was the right part and worked great
Guest -
July 24, 2019
Verified Purchase
Could be a little longer
The parts showed up quickly
Guest -
August 23, 2021
Verified Purchase
Great parts kinda slow shipping only bad part
All the parts for the saw worked great fixed all problems.
Guest -
April 27, 2020
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Hose
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Prime bulb return line dry rotted, leaking gas.
brandon - September 11, 2016
👍 3 of 3 people found this instruction helpful
Tool Type
Chain Saw
Difficulty
Hard
Time
1-2 hours
Tools Used
Screwdriver, Pliers, Nutdriver, Two picks, one straight, one 90 degrees, knife
1. Remove chain and bar( for easy maneuverability), empty gas in tank, then top cover, followed by handle and throttle grip. The throttle has to be disconnected from carb, and you have to spin the linkage to remove because it does not come straight out.
2. You can choose to remove carb, I was able to do repair without removing, probably more difficult, but might have saved a little time. I removed return line and fuel lines and prime bulb from saw, followed by grommets. To remove fuel line you have to open gas tank and pull out filter and fuel line with your 90 degree pick. Remove filter and hose, replace with new.
3. When I replaced grommets and hose, I put a little oil on them to make things go on a little easier. I found it is easier to install grommets on hose first and then install grommets on saw. You can always push and pull hose through.
4. Once all hoses are on and secure, reinstall your filter on line and replace inside tank. I cut about two inches off the tank line before installing filter, just because it seemed a little long, your choice. I only had one line that was bad, but I figured while I was replacing one, might as well do them all, the others are probably going to fail soon.
5. In order to replace exhaust screen, you will have to remove chain break handle, two hex head bolts, slide screen out, slide new one in and done.
6. Once installed, I reassembled everything in the reverse order it come out. Chain brake handle, main handle then throttle cover, remember to install throttle linkage, you have to spin it to get back next to the carb, this can be a little tedious, but make sure it is where it needs to go before bolting main handle on, or you have to take it apart again(my mistake).
7. After throttle cover, replace your top cover, and chain and bar, add gas and your good to go.
2. You can choose to remove carb, I was able to do repair without removing, probably more difficult, but might have saved a little time. I removed return line and fuel lines and prime bulb from saw, followed by grommets. To remove fuel line you have to open gas tank and pull out filter and fuel line with your 90 degree pick. Remove filter and hose, replace with new.
3. When I replaced grommets and hose, I put a little oil on them to make things go on a little easier. I found it is easier to install grommets on hose first and then install grommets on saw. You can always push and pull hose through.
4. Once all hoses are on and secure, reinstall your filter on line and replace inside tank. I cut about two inches off the tank line before installing filter, just because it seemed a little long, your choice. I only had one line that was bad, but I figured while I was replacing one, might as well do them all, the others are probably going to fail soon.
5. In order to replace exhaust screen, you will have to remove chain break handle, two hex head bolts, slide screen out, slide new one in and done.
6. Once installed, I reassembled everything in the reverse order it come out. Chain brake handle, main handle then throttle cover, remember to install throttle linkage, you have to spin it to get back next to the carb, this can be a little tedious, but make sure it is where it needs to go before bolting main handle on, or you have to take it apart again(my mistake).
7. After throttle cover, replace your top cover, and chain and bar, add gas and your good to go.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Broken fuel line
William - February 16, 2024
Tool Type
Chain Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, 12-2 romex
Parts Used
R&R old fuel line & grommet
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Fuel hoses leaking/deteriorating.
John - September 26, 2020
Tool Type
Chain Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Pliers, surgical hemostat
Parts Used
It went well. Using pliers and a surgical hemostat, I threaded the hoses into position. Works great now.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Wear and tear, leaking bar oil, fuel lined cracked and running lean,
ROBERT - April 17, 2020
Tool Type
Chain Saw
Difficulty
Medium
Time
More than 2 hours
Tools Used
Screwdriver, Pliers, Socket set, Wrench Set
Watched u-tube videos for each individual repair
Did you find this story helpful?
Thanks for voting and helping fellow customers!
hard starting
richard - January 24, 2019
Tool Type
Chain Saw
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, sheet rock knife
replace the above parts along with the primer bulb
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air purge bubble had cracked and decided to change connected hoses as well.
Brian - June 29, 2017
Tool Type
Chain Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Pliers
Took off top cover, disconnected hoses, disconnected air purge assembly and attached new assembly, attached hoses, replaced cover, poured in fuel/oil mixture, primed the air purge, and started the chainsaw right up for the first time in 3 years with only 3 pulls. Works great with zero problems.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
