*This part replaces obsolete part #: 151281-06.
Product Information
Description:
| The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. |
Frequently Purchased With
Compatibility
the 36 compatible machines
This part is compatible with the following machines:
DeWALT
DW421 Type 1 Random Orbit Sander
DW421 Type 2 Random Orbit Sander
DW422 Type 1 EVS Random Orbit Palm Sander
DW423 Type 1 5 inch EVS Random Orbit Sander
DW423 Type 2 5 inch EVS Random Orbit Sander
D26453 Type 1 Random Orbit Sander
D26450 Type 1 Random Orbit Sander
D26451 Type 1 Random Orbit Sander
D26456 Type 1 5" Palm Grip Sander
DW26451K Type 1 5 Random Orbit Sander
DW26453K Type 1 5 Random Orbit Sander
DW421K (Type 1) 5 R.O.S in Kitbox
DW421 Type 2 Random Orbit Sander
DW422 Type 1 EVS Random Orbit Palm Sander
DW423 Type 1 5 inch EVS Random Orbit Sander
DW423 Type 2 5 inch EVS Random Orbit Sander
D26453 Type 1 Random Orbit Sander
D26450 Type 1 Random Orbit Sander
D26451 Type 1 Random Orbit Sander
D26456 Type 1 5" Palm Grip Sander
DW26451K Type 1 5 Random Orbit Sander
DW26453K Type 1 5 Random Orbit Sander
DW421K (Type 1) 5 R.O.S in Kitbox
DW421K (Type 2) 5 R.O.S in Kitbox
DW423K (Type 1) 5in Evs Ro Sander Kit
DW423K (Type 2) 5in Evs Ro Sander Kit
D26451K (Type 1) 5 Random Orbit Sander
D26453K (Type 1) 5 Random Orbit Sander
D26451-AR (Type 1) 5-Inch Ro Sander Power Tool
D26451-B2 (Type 1) 5-Inch Ro Sander Power Tool
D26451-BR (Type 1) 5-Inch Ro Sander Power Tool
DW421-AR (Type 3) Random Orbital Sander Power Tool
DW421-B2 (Type 1) Random Orbital Sander Power Tool
DW421-B3 (Type 1) Random Orbital Sander Power Tool
DW423K (Type 1) 5in Evs Ro Sander Kit
DW423K (Type 2) 5in Evs Ro Sander Kit
D26451K (Type 1) 5 Random Orbit Sander
D26453K (Type 1) 5 Random Orbit Sander
D26451-AR (Type 1) 5-Inch Ro Sander Power Tool
D26451-B2 (Type 1) 5-Inch Ro Sander Power Tool
D26451-BR (Type 1) 5-Inch Ro Sander Power Tool
DW421-AR (Type 3) Random Orbital Sander Power Tool
DW421-B2 (Type 1) Random Orbital Sander Power Tool
DW421-B3 (Type 1) Random Orbital Sander Power Tool
Porter Cable
343 Type 1 5" Random Orbit Sander
343VS Type 1 5" Variable Speed Random Orbit Sander
343VS Type 2 5" Variable Speed Random Orbit Sander
390 Type 1 5" Low Profile Random Orbit Sander
382 Type 1 5 Palm Grip R.O. Sander
343VS Type 1 5" Variable Speed Random Orbit Sander
343VS Type 2 5" Variable Speed Random Orbit Sander
390 Type 1 5" Low Profile Random Orbit Sander
382 Type 1 5 Palm Grip R.O. Sander
390K Type 1 Sander
343K (Type 1) Sander
343VSK (Type 1) 5 Random Orbit Sander
343VSK (Type 2) 5 Random Orbit Sander
382 (Type 2) 5 Palm Grip R.O.Sander Power Tool
343K (Type 1) Sander
343VSK (Type 1) 5 Random Orbit Sander
343VSK (Type 2) 5 Random Orbit Sander
382 (Type 2) 5 Palm Grip R.O.Sander Power Tool
Black and Decker
Products Compatibility
This item works with the following types of products:
- • Sander
Repair Guides
![]()
Watch the Repair Video for
Hook And Loop Sander Pad
Articles:
|
Step-by-step instructions for removing and installing the hook-and-loop sanding pad on your Porter Cable sander....
January 11, 2018
|
Questions & Answers for Hook And Loop Sander Pad
Will this fit the DWE6421K
Michael
for model number DWE6421K
asked on 2024-01-05
Hi Michael, Thank you for writing. The Pad Assembly for this model is listed as Part Number: N329079. We hope this helps!
eReplacementParts Team January 05, 2024
Is this pad exclusive to Dewalt sanders? I have an older Porter Cable sander that looks much the same
William
asked on 2023-10-31
Hello William, Thank you for the question. This Pad fits some models for Porter Cable, DeWALT and Black and Decker. In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you!
eReplacementParts Team October 31, 2023
Will this work for Model 333? I would like to switch from 5 hole to 8 hole sanding paper
Dennis
for model number Porter Cable model 333
asked on 2023-04-20
Hi Dennis,
Thank you for your question. This pad is not listed for your sander. An 8-hole hook and loop sander pad is listed for your sander. The part number for the 8-hole sander pad is 885119. We hope this helps!
eReplacementParts Team April 20, 2023
black and decker quantum pro 5 inch orbital sander pad. i think it is 0800 type 1.. the pad that holds the sandpaper.. which one do i need
Eric
asked on 2023-03-03
Hi Eric,
Thank you for your question. We were unable to find a parts list with the model number you provided and before we can provide you with information on the pad, we will need the model number from your sander. The model number will be found on a rating label or name plate. If you could resubmit your question with this information, we would be happy to help you. We look forward to hearing from you!
eReplacementParts Team March 03, 2023
Will the self adhesive paper work with part # 151281-08
John
for model number D26450
asked on 2023-01-13
Hello John, thank you for the question. The Hook and Loop Pad takes the Velcro Sand Paper with hook and loops. We hope this solves your problem!
eReplacementParts Team January 13, 2023
Hi, The foam padding that holds the sanding pads has released from the tool. What should I get to fix this?
Jennifer
for model number 343 type 1
asked on 2022-09-15
Hello Jennifer, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part Number 151281-08. Thank you for your inquiry, good luck with this repair!
eReplacementParts Team September 15, 2022
Will this work on my model?
James
for model number 382
asked on 2022-09-01
Hello James, thank you for your question. Yes, this will work on your Porter Cable 382. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
eReplacementParts Team September 01, 2022
Repair Instructions: Submitted by Customers Like You
36 of 38 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Hook and loop would not hold sandpaper
Removed three screws holding old pad and replaced with new one. Easy repair that saved the price of a new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
13 of 15 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Torx style screwdriver
The original sander pad had deteriorated.
The only special tool you will need is a torx style screwdriver. It is a simple matter of removing the 3 screws that hold the pad to the sander and it should only take a couple minutes to remove and replace the sander pad.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
10 of 12 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Replaced the sander pad
Took off the old pad by removing the 3 screws holding it on. Put the new pad on. Then began to use the repaired sander. Instead of spending over $70, total cost was a little over $20.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 6 people found this instruction helpful
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Bad switch and pad wore out.
Removed top cap of sander. Noted where the wires where located on the switch. Removed switch cover. Connected the wires to the new switch. Put switch cover on, then installed new switch and put switch cap on. For the pad. I removed the 3 screws from the old pad, and put the new pad on the sander with the 3 screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sanding pad was breaking apart due to dry rot
Unscrew the 3 screws holding sanding pad on
Remove old pad
Screw new pad back on orbital sander
Remove old pad
Screw new pad back on orbital sander
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sanding pad was coming apart.
Removed old pad & installed new one. It was very easy only three screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Just a flathead screwdriver
Velcro pad worn out and brake and springs severely worn.
Unplug sander, remove pad screws, take off pad and remove break. Springs are located on brake. Remove springs and install new ones and if the break pad is worn and speed cannot be controlled, replace break pad and springs. Place new or repaired break assembly on sander, and then Velcro pad and insert the 3 retaining screws. Plug back in and get to work!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Polisher
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, torex
Worn pad
Remove 3 screws from old pad. Install the new pad with the screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Nutdriver
Sanding pad was worn out and the bearing retainers were broken
Replaced all broken and worn parts
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Hooks were worn out
Replaced pad. Easy off with the old, on with the new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
133 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
125
4 stars
6
3 stars
0
2 stars
1
1 stars
1
< PREV
- 1
- 2
- 3
Palm sander pad
Fit perfectly, arrived quickly
Guest -
21 days ago
Verified Purchase
2nd replacement pad in 20+ years
You don't realize how much these pads degrade until you replace them. Easy to do, Shipping cost seemed a bit much for such a small item
Guest -
March 9, 2024
Verified Purchase
Fit perfectly
My orbital sander was old and I was so happy to find this part that went on easily and fits! I’ll always use EReplacement Parts because I can find what I need.
Roxanna -
March 9, 2024
Verified Purchase
The correct part
The replacement part was exact replacement.
Guest -
March 1, 2024
Verified Purchase
Orbital Sanding Pad
The replacement parts were an exact matched and I am very pleased with the delivery and part. I will use this site again when the need arises.
Guest -
December 20, 2023
Verified Purchase
Perfect replacement part
Arrived quickly and works as well as original part. I had tried cheaper replacement part that had a plastic backing which failed immediately. This part has aluminum backing and I expect it to last for years.
Steve -
December 5, 2023
Verified Purchase
Great response, part was just what I needed.
Exactly what I wanted and needed. Fits perfectly.
Guest -
December 1, 2023
Verified Purchase
So quick and easy perfect
Perfect fit shipping great 1 stop and buy
Guest -
November 20, 2023
Verified Purchase
Pad replacement
My original hook and loop pad dry rotted and fell apart so I ordered a new one and it works very well. I hope it's a better material that will last longer. It was packaged well and arrived quickly
Guest -
September 13, 2023
Verified Purchase
Sander Pad
Completely satisfied with part, shipping---Thank you Ken
Guest -
September 11, 2023
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
- 2
- 3
Product Information
Repair Guides
![]()
Watch the Repair Video for
Hook And Loop Sander Pad
Articles:
|
Step-by-step instructions for removing and installing the hook-and-loop sanding pad on your Porter Cable sander....
January 11, 2018
|
